Assembly Instructions Instruction Manual

ManualsBrandsAnthro ManualsFurnitureElevate II Single Surface

ASSEMBLY INSTRUCTIONS

Anthro Corporation

| 10450 SW Manhasset Dr. | Tualatin, OR 97062

Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com

Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409

Elevate II

Rev C, September 2013

Product Part#

Elevate II Basic 48w 23.5d MVAS48SS/xx

Elevate II Basic 48w 29d MVAD48SS/xx

Elevate II Plus 48w 23.5d MVBS48SS/xx

Elevate II Plus 48w 29d MVBD48SS/xx

Certiﬁcation: Elevate II is certiﬁed by ETL to UL962 standard for Commercial and Household furnishings.

Product Part#

Elevate II Basic 60w 23.55d MVAS60SS/xx

Elevate II Basic 60w 29d MVAD60SS/xx

Elevate II Plus 60w 23.5d MVBS60SS/xx

Elevate II Plus 60w 29d MVBD60SS/xx

Summary of content (8 pages)

PAGE 1
A S S E MB LY I NSTR U C TI ONS Elevate II Product Part# Product Part# Elevate II Basic 48w 23.5d MVAS48SS/xx Elevate II Basic 60w 23.55d MVAS60SS/xx Elevate II Basic 48w 29d MVAD48SS/xx Elevate II Basic 60w 29d MVAD60SS/xx Elevate II Plus 48w 23.5d MVBS48SS/xx Elevate II Plus 60w 23.5d MVBS60SS/xx Elevate II Plus 48w 29d MVBD48SS/xx Elevate II Plus 60w 29d MVBD60SS/xx Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062 Toll-free: 800.325.3841 | Fax: 800.325.
PAGE 2
IM P O RTA N T S AF E T Y I NST R U C T I O NS When using an electrical furnishing, basic precautions should always be followed, including the following. Read all instructions before using Elevate II Adjusta. DAN GE R To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet before cleaning. WA RNING To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Unplug from outlet before putting on or taking of parts. 2.
PAGE 3
08 01 03 13 05 06 04 10 11 07 12 19 W E L CO ME PA R TS LI ST Thank you for purchasing Anthro's Elevate II electric lift table! Before beginning assembly of your table, please review the parts list to verify that your shipment is complete. If you have any questions or if we can help you in any way, please contact us at 800.325.3841.
PAGE 4
STEP 1 - AT TA C H G U S S E T S TO TO P Lay the worksurface upside down on a cushioned, non-marring surface. Locate the front edge of the table. On Plus tables, the front of the table has a sloping waterfall edge. On the Basic tables, the back edge of the table has the seam where the edgebanding meets. Align the Leg Gussets with the holes on the top so the upright flange faces the outside of the table and the tapering end points to the front of the table.
PAGE 5
STEP 3 - INS TA L L T H E C R O S S PA N Align the Cross Pan with the Leg Assemblies so the pair of flanges on the pan line up with the pre-drilled holes on the table. Attach the back of the pan to the top with four 1" Button Hd PB Screws (325-5580-00) Attach the front of the pan to the top with three more 1" Button Hd PB Screws (325-5580-00). Attach the pan to each Leg Housing with two M6-10MM Button Hd Screws (325-5503-00) using the Anthro driver. Tighten all fasteners.
PAGE 6
STEP 4B - INS TA L L C O N T R O L B OX A ND K EYPA D - SHA LLOW TA B LES Align the keypad and its slider housing with the four pre-drilled holes at the front of the keyboard surface so the buttons are face-down at the front edge of the keyboard surface and the flat side of the housing is against the shelf. The keypad can also be installed directly to the worksurface without the slider housing, either so it extendds in front of the table or so it's set back a bit.
PAGE 7
STEP 6 - INS TA L L F E E T A N D H OM E TH E LEG S Align one foot with each leg so the wheels are at the back. Attach the foot to the leg with four M6x20 Socket-head Screws using the Anthro driver. Repeat for the other foot. With the help of another person, carefully rotate the table onto its feet. Plug in the table and use the keypad to move the table all the way down. Release the button and press it again to home the legs so they move in unison.
PAGE 8
TROUBL E S H O OT I N G G U I D E Is the table giving you trouble? Try these steps first. Still need help? Contact Anthro at 800.325.3841. Table won't go up, but it will go down. Inspect the leg cables, control box cable, and power cable to be sure they are connected properly and not damaged. Need replacements? Contact Anthro at 800.325.3841. Lower the table to its lowest position, release the button, the press the DOWN button again for 5 seconds to home the legs.