A s s e mbly instructions eNook II ® Part Number: EK3616zz/xx NOTE: The eNook additional shelves shown above are not included. Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062 Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.
03 05 14 10 12 04 11 01 13 02 06 07 08 welcome PA RTS LIST Thank you for purchasing eNook®! These instructions are for Anthro’s eNook.™ Before beginning assembly, please take a moment to review the parts list below to verify that your shipment is complete. This installation is a two person job. If you have any questions or if we can help you in any way, please contact us at 800.325.3841.
STE P 1 Select the Mounting Location ¡ When choosing the right place to install your eNook, be sure to check the location of your power source. The power cord that comes with your eNook is 6 ft long. ¡ Your eNook can be mounted to drywall or to wood wall studs. If you’re installing to wood wall studs, go to Step 2. ¡ If you’re installing into drywall, go to Step 7 STE P 2 Find Wall Studs ¡ Using a stud finder, locate the studs to which you'll attach your eNook.
STE P 5 Lift eNook Frame onto screws ¡ Lift the eNook frame onto the first mounting screw. Keyhole slots on the frame are spaced every 2", so you can position the eNook where you want it. ¡ While one person holds the eNook frame level, the second person marks the installation point of the second 1-1/2" long screw. Make sure that the second screw goes into a stud, too! ¡ Remove the frame from the wall and drill the second hole with the 1/8" drill bit.
STE P 8 Install one TOGGLER™ for Drywall Installation ¡ Drill 1/2” diameter hole in your wall at the mounting point. A ¡ Insert a TOGGLER into a hole, metal end first. ¡ Pull the plastic ring end so the metal channel rests flush behind the wall. With your other hand, slide the plastic cap along the straps until the flange of the cap is flush with the wall. ¡ Place your thumb between the plastic straps. Push side to side, snapping off the straps at the wall.
STE P 10 Insert Screw and Install Frame ¡ Insert one 1-5/8" long screw into the top two TOGGLERs, but don’t tighten all the way. Leave the screw head about 1/4" from the plastic cap. ¡ Lift the Frame onto the top two screws. Install the bottom two screws, then tighten down all four screws. STE P 11 Install Four Fasteners onto Main Unit ¡ Using your Hex Driver, install two black Workstation Screws onto the side walls, but don’t tighten all the way.
STE P 1 3 Insert the Bottom Tray ¡ Place the Bottom Tray on the eNook shelf so that the logo on the tray faces out. Tab ¡ Align the 2 holes on the back of the Tray with the pins on the Frame. ¡ Slide the Tray into place. Attach the tray to the left and right of the frame using 4 workstation screws. Do not tighten these screws all the way. Pins Notch ¡ Install the cover plates, one on the left and one on the right of the Tray.
STE P 1 5 Insert Power Strip ¡ Open the bottom door on eNook and slide the Power Strip inside. STE P 1 6 Insert Cable Clips ¡ Cable Clips are provided to help manage your cables. Clips can be poked into any of the ventilation holes on the top, back, or side of eNook. ¡ Twist the ends of the clips to keep the cables in place. Congratulations! Your assembly is complete! Questions? Call us at 800.325.3841 or visit anthro.com.
Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062 Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409 *300-5394-00* 300-5394-00 Warranty: eNook has a five year warranty. Notices: Technology Furniture and eNook are trademarks of Anthro Corporation. Patent Pending. Anthro reserves the right to modify the design and specifications without prior notice.
