Approved Copy ® O o W ne n O . rld a m eS o h C rt ™ .
TABLE OF CONTENTS Approved Copy 1 INTRODUCTION 1-2 NM 14/19 BATTERY MODULE DISASSEMBLY 3 NM 14/1919 BATTERY MODULE ASSEMBLY 4-5 NM 28/38 BATTERY DISASSEMBLY 5-6 NM 28/38 BATTERY ASSEMBLY 7 LIMITED WARRANTY
INTRODUCTION Approved Copy The CINE VCLX series of batteries are designed and manufactured to the high quality expected from all Anton/Bauer batteries. Because of the specialized and proprietary circuitry that is used in these batteries, the cells inside of any CINE battery must be replaced with an NM14/19 or NM28/38 module. The NM14/19 and NM28/38 modules eliminate the need for “re-celling”, long waiting periods and unnecessary shipping of the CINE® batteries.
NM 14/19 BATTERY MODULE DISASSEMBLY OF UNIT (CONTINUED) Approved Copy STEP 3 STEP 5 Remove the rubber band from the coiled harness and disconnect the 2 connectors as shown in figure E. Remove the rubber side plate assembly from the unit as shown in figure C. Figure C STEP 4 Remove the (1) 6-32 x 5/16 screw from the sheet metal case. Slide the battery cell assembly from the electronics assembly as shown in figure D.
NM14/19 RE-ASSEMBLY OF UNIT Approved Copy STEP 1 STEP 3 Plug the 2 connectors exiting from the battery cell assembly to the mating connectors of the electronics assembly as shown in figure F. Install the (4) 6-32 x 3/8 washers and screws as shown in figure H. 6-32 screw QTY 4 Figure H Figure F STEP 2 STEP 4 Coil the excess harness and wrap with the rubber band. Slide the battery cell assembly into the electronics assembly.
NM 28/38 BATTERY DISASSEMBLY OF UNIT Approved Copy STEP 1 Remove the (4) #10 screws and (4) # 10 washers as shown in figure A. NOTE: Do not remove handle or handle hardware from side plates. STEP 3 Remove the rubber side plate assembly from the unit as shown in figure C. #10 screw QTY 4 Figure A Figure C STEP 2 STEP 4 Remove the (4) 6-32 screws and (4) 6-32 washers as shown in figure B Remove the (1) 6-32 x 5/16 screw from the sheet metal case.
NM 28/38 BATTERY DISASSEMBLY OF UNIT (CONTINUED) Approved Copy STEP 5: Remove the rubber band from the coiled harness and disconnect the 2 connectors as shown in figure E. Figure E NM 28/38 BATTERY RE-ASSEMBLY OF UNIT STEP 1 STEP 2 Plug the 2 connectors exiting from the battery cell assembly to the mating connectors of the electronics assembly as shown in figure F. Coil the excess harness and wrap with the rubber band. Slide the battery cell assembly into the electronics assembly.
NM 28/38 BATTERY RE-ASSEMBLY OF UNIT (CONTINUED Approved Copy STEP 3 Install the (4) 6-32 x 3/8 washers and screws as shown in figure H. 6-32 screw QTY 4 Figure H STEP 4 Install (4) #10 washers and screws as shown in figure I.
BATTERY LIMITED WARRANTY Approved Copy 0-12 MONTHS - “Anton/Bauer will repair or replace the product at Anton/ Bauer’s option - FREE OF CHARGE.” This limited warranty for the product specified in this document is given by Anton/Bauer, Inc. (“Anton/Bauer”), 14 Progress Drive, Shelton, Connecticut 06484.
Approved Copy The following are trademarks of Anton/Bauer, Inc.: Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique, DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac, Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design, Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World.
