TM250HD HD encoder DVB-T/DVB-C/IP out USER MANUAL V1.
TM250HD USER MANUAL Congratulations on your purchase of the TM250HD ! This ‘state of the art’ product, is a HD encoder. The video input can be taken from HDMI, PC or Component Video. The audio can be taken from HDMI or analog audio. After compressing the video into H264 and audio in AAC, the output can be configured as DVB-T, DVB-C modulator or as IP streamer. Stand-alone configuration is made easy through 4 tact switches and ergonomic menu’s.
TM250HD USER MANUAL 1 - Safety considerations 1.1 CONNECTING TO THE MAINS SUPPLY This product has to be connected to the mains supply. If there is the slightest doubt concerning the type of connection available on the installation, please contact your supplier of electricity. Before carrying out maintenance operation or modification of the installation, the modulator has to be disconnected. Remark : only use the supplied power adaptor. 1.
TM250HD USER MANUAL 2 - Description of the different elements C1 C2 C3 C4 C5 Power supply input (5V/4A) USB input (for programming the TM250HD by PC) Ethernet connection RJ45 RF input RF output C1 C2 DC input C3 USB C6 C6 C7 C8 C9 HDMI input Component video input PC input Analog audio input C7 C4 C5 INPUT OUTPUT C8 COMPONENT VIDEO INPUT Pb Y Pr C9 AUDIO INPUT L R HDMI HD encoder DVB-T / DVB-C / IP output A1 T1 T2 T4 T3 TM250HD A1 Display T1 CANCEL/RETURN button T2 ENTER button
TM250HD USER MANUAL 3 - Installation and menu structure 3.1 - Installation Install the TM250HD against a wall using the wall fixation brackets to ensure cooling of the housing through natural convection. ( see drawing) Connect the audio and video source using HDMI, PC, or component VIDEO and ANALOG audio cables. Connect the RF input cable (if present) and the RF output cable. If the RF input is not used, please connect a 75 ohm terminating resistor to it.
TM250HD USER MANUAL 3.3 - Menu structure The TM250HD has different menus allowing easy access to the differents parameters and to change them when necessary. Below you will find the structure of the different menus. CONFIGURATION MAIN MENU IP-STREAMER DVB-T MODULATOR DVB-C MODULATOR CONFIGURATION DVB SETTINGS IP SETTINGS A/V SETTINGS TS SETTINGS LANGUAGE DEFAULT CONFIG.
TM250HD USER MANUAL 4 - Setting up the TM250HD 4.1 - The CONFIGURATION menu In this menu you can setup your TM250HD as IP streamer, DVBT modulator or DVBC modulator. Select the appropriate option with the buttons u and t and press the ENTER button to confirm. CONFIGURATION IP-STREAMER DVB-T MODULATOR DVB-C MODULATOR 4.
TM250HD USER MANUAL 4.2.1 - Setting DVB-T parameters FREQUENCY BANDWIDTH ATTENUATION DVB-T When you select DVB-T and press the ENTER button, the following submenu appears. It allows you to set the DVB-T parameters. MODE CONSTELLATION F.E.C. GUARD INTERVAL 2K 8K Select the mode MODE CONSTELLATION F.E.C. GUARD INTERVAL QPSK QAM16 QAM64 Select the constellation MODE CONSTELLATION F.E.C. GUARD INTERVAL 1/2 2/3 3/4 5/6 7/8 Select the F.E.C. MODE CONSTELLATION F.E.C.
TM250HD USER MANUAL 4.3 - The IP settings menu When your TM250HD is configured as IP streamer, the you can adjust the settings in the IP settings menu. PROTOCOL IP ADDRESS UDP PORT TS OVER UDP TS OVER RTP PROTOCOL IP ADDRESS UDP PORT IP ADDRESS 192.168.1.15_ 8 Xfbc0123456789 PROTOCOL IP ADDRESS UDP PORT UDP PORT 1234_ 8 Xfbc0123456789 IP SETTINGS PROTOCOL IP ADDRESS UDP PORT Select UDP or RTP Set the IP ADDRESS Set the UDP PORT nr. 4.
TM250HD USER MANUAL 4.4.2 - Changing the AUDIO settings Select the audio input VIDEO SETTINGS AUDIO SETTINGS AUDIO INPUT AUDIO RATE HDMI-PCM VOLUME HDMI ANALOG AUDIO Select the audio bitrate AUDIO INPUT AUDIO RATE HDMI-PCM VOLUME 192 Kb/s 256 Kb/s 320 Kb/s 384Kb/s Select the audio volume AUDIO INPUT AUDIO RATE HDMI-PCM VOLUME x1 x2 x4 4.5 - The TS settings menu This menu allows you to adjust specific parameters of the transport stream. TS SETTINGS NIT RELEASE NET ID. ORIG. NET. ID.
TM250HD USER MANUAL NET ID. ORIG. NET. ID. NETWORK NAME TS ID. TS ID. 100_ 8 Xfbc0123456789 Set the Transport Stream ID. ORIG. NET. ID. NETWORK NAME TS ID. PROGRAM ID. PROGRAM ID 1_ 8 Xfbc0123456789 Set the PROGRAM ID. NETWORK NAME TS ID. PROGRAM ID. LCN ID. EACEM ITC Select the LCN ID. TS ID. PROGRAM ID. LCN ID. L.C.N. L.C.N. 1_ 8 Xfbc0123456789 Set the LCN number. PROGRAM ID. LCN ID. L.C.N. HD L.C.N. HD L.C.N. 1_ 8 Xfbc0123456789 Set the HD LCN number. PROGRAM ID. LCN ID. L.C.N.
TM250HD USER MANUAL 5 - Programming using a PC The settings of the TM250HD can also be changed using a PC. First, please install the software TMHDIFace on your PC. You can download this software from our internet site anttron.com After installation of this software, connect the TM250HD using a USB cable (not included) to your personal computer. Then launch the program TMHDIface. On the display of the TM250HD the message appears, indicating that the programming is now performed through your PC.
