MANUFACTURING NUMBERS: 9700501 9700505 9700508 9700512 WATER FILTRATION SYSTEM Model SE-4200/4400 P/N 1010852 Rev.
SE-4200/4400 WATER FILTRATION SYSTEM TABLE OF CONTENTS Owner Information .....................................................2 General ......................................................................2 Warranty Information .................................................2 Service/Technical Assistance ....................................3 Important Safety Information ....................................3 Operating Specifications............................................5 Specifications .............
SE-4200/4400 WATER FILTRATION SYSTEM Service/Technical Assistance Purchased From: If you experience any problems with the installation or operation of your unit, contact Antunes Filtration Technologies at 1-630-784-1000 or toll free in the United States at 1-800-253-2991. Date of Purchase: Model No.: Serial No.: Fill in the information in the next column and have it handy when calling for assistance. The serial number is on the specification plate on the unit. Mfg. No.: IMPORTANT A.J. Antunes & Co.
SE-4200/4400 WATER FILTRATION SYSTEM IMPORTANT SAFETY INFORMATION (continued) The following warnings and cautions appear throughout this manual and should be carefully observed. • Turn the unit off, disconnect the power source, and allow unit to cool down before performing any service or maintenance on the unit. • The equipment should be grounded according to local electrical codes to prevent the possibility of electrical shock.
SE-4200/4400 WATER FILTRATION SYSTEM SPECIFICATIONS Electrical Ratings Voltage Watts Amps Hertz SE-4200 9700501 & 9700505 120 150 1.25 50/60 SE-4400 9700508 & 9700512 230 150 .75 50/60 Model & Mfg. # WARNING ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH. Electrical Cord & Plug Configurations Letter Code* Description C Commercial Cord Configuration CEE 7/7, 16 Amp., 250 VAC (Assembly Only). (C)F*** 5-15P, 15 Amp.
SE-4200/4400 WATER FILTRATION SYSTEM SPECIFICATIONS (continued) Dimensions A B Control Box Drain Permeate (use water) C Inlet 6 P/N 1010852 Rev.
SE-4200/4400 WATER FILTRATION SYSTEM INSTALLATION When making a plumbing connection to the system, remember to use a back-up wrench on the support plumbing. Always use a good quality and approved pipe sealant or Teflon tape on pipe threads. Unpacking The carton should contain the filtration system and an information packet. • SE-4200 or SE-4400 • Information Packet Be careful not to get the pipe sealant inside the pipe when making the connections. Do not over tighten the connections. 1.
SE-4200/4400 WATER FILTRATION SYSTEM INSTALLATION (continued) Locating and Mounting the system be installed in the water line after the permeate connection. This will help prevent possible contamination of the filter system due to other equipment downstream. The check valve (not supplied) should be mounted close to the system outlet, and sized properly for the plumbing line. Check with local codes for the proper specification.
SE-4200/4400 WATER FILTRATION SYSTEM INSTALLATION (continued) FLUSHING AND STARTING THE SYSTEM SANITIZING THE SYSTEM AND LINES To ensure that the highest quality water is produced from the system, the plumbing leading from the filter system must be flushed clear of all debris after the system is hooked up. After making the connection to the outlet of the filter system, open a faucet or tap closest to the filter system, then slowly open the inlet water valve.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION Filtration Process Operating Controls (Figure 2) The filtration process includes a Filtration Cycle and a Backwash Cycle. Control Button During the Filtration Cycle, water enters the system inlet port and passes through the filter elements before exiting via the Permeate outlet. This system is designed so that no valves are powered during the Filtration Cycle.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION (continued) Programming Using the Up and Down arrow buttons, enter the correct date in mm/dd/yy format. After each entry, press the Enter button. For example, for June, set the month as 06 and then press the Enter button. Set the date and year in this same manner. 1. Once the system is connected to a power source, the unit displays the following messages in the table below in order: Message Description ANTUNES FILTRATION Rev. 00.00.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION (continued) SET FLUSH CYCLE MODE SET QUICKFLUSH MODE 1. From the FILTER MODE display, press the Stop button. The system switches to STOP MODE and displays the STOP MODE display. NOTE: The Quick Flush function allows the system to be used for water systems containing a high quantity of air. Air does not pass through the filtration membranes. Performing a quick flush at pre-set times allows the accumulated air to be released. 2. Press the Menu button. 3.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION (continued) RESET DEFAULTS MODE 7. The system displays the FLUSH BY PRESS DIFF display. If the filtration system came with pressure transducers installed, this feature is available. If no transducers are installed, this feature is ignored. The default value is on. This should be appropriate for most locations. Use the Left and Right Arrow Buttons to make the desired change and then press the Enter button. 1.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION (continued) NOTE: The REVIEW HISTORY mode displays information about the most recent operation first. 5. The system displays the SET ENABLE PASSWORD display. The default setting is off. If you do not want to use a password, press the Enter button. The system will then display the SELECT LANGUAGE display. The default setting is English (other languages are not available at this time). Press the Enter button to accept the default. 5.
SE-4200/4400 WATER FILTRATION SYSTEM OPERATION (continued) Operating the Unit WARNING Once a password has been activated, that password will be required to change any settings. DO NOT lose your password! Keep it in a safe place. Contact the manufacturer if you have lost your password. After all of the menus have been programed, the system can be activated. 1. To start the filtration operation, press the RUN button. The system will perform a BORE AIR RELEASE function and return to FILTER MODE.
SE-4200/4400 WATER FILTRATION SYSTEM MAINTENANCE The SE-4200/4400 Filtration system is designed to require very little maintenance. To ensure that the water is of the highest quality, occasionally some service is required. 6. Inset the new cartridge into the system Checking the Controller Program 8. Inspect the O-rings to make sure they are clean and are not splitting or cut. For all O-rings, make sure they are lubricated with an approved food grade lubricant acceptable for drinking water use. 7.
SE-4200/4400 WATER FILTRATION SYSTEM TROUBLESHOOTING Problem Possible Cause Unit does not have power. The power cord is not correctly plugged in. Plug power cord in correctly. The Control Display is blank. The power cord is not correctly plugged in. Plug power cord in correctly. Control Board is inoperable. Transformer is inoperable. Contact your maintenance person or Authorized Service agency. Unit in “STOP” mode Set unit to “RUN” mode. Optional Inlet Valve (if installed) is closed.
SE-4200/4400 WATER FILTRATION SYSTEM TROUBLESHOOTING (continued) Problem Water leaks from Permeate Port. Water leaks from system fitting or connection. Possible Cause Corrective Action Permeate Port not tight. Tighten with strap wrench if necessary. O-rings not lubricated. Lubricate O-rings with food-grade lubricant. O-rings split, cut, or twisted. Replace O-rings. Not enough pipe thread sealant used. Redo fitting with proper amount of sealant. Fitting loose or broken.
SE-4200/4400 WATER FILTRATION SYSTEM REPLACEMENT PARTS - SE-4200/4400 22 22a 21 25 47 23 26 28 29 65 30 See Inset A 33 47 47a 34 36 32 35 37 48 31 38 39 40 41 42 8 9 11 Inset A 10 12 13 14 43 45 1 2 16 15 18 17 5 20 P/N 1010852 Rev.
SE-4200/4400 WATER FILTRATION SYSTEM REPLACEMENT PARTS - SE-4200/4400 (continued) Item Part No.
SE-4200/4400 WATER FILTRATION SYSTEM WIRING DIAGRAM P/N 1010852 Rev.
SE-4200/4400 WATER FILTRATION SYSTEM NOTES 22 P/N 1010852 Rev.
SE-4200/4400 WATER FILTRATION SYSTEM NOTES P/N 1010852 Rev.
LIMITED WARRANTY Equipment manufactured by Antunes Filtration Technologies, Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from mechanical and electrical defects for a period of one year from date of purchase or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when installed in accordance with manufacturer’s recommendations.