MANUFACTURING NUMBERS: 9200560 9200600 9200602 9200606 9200608 9200614 9200616 9200620 9200622 9200624 9200626 9200628 9200629 9200630 9200631 9200632 9200634 9200638 9200640 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER TABLE OF CONTENTS Owner Information......................................................2 General.......................................................................2 Warranty Information..................................................2 Service/Technical Assistance.....................................3 Important Safety Information.....................................3 Specifications..............................................................
VERTICAL CONTACT TOASTER OWNER INFORMATION (continued) Service/Technical Assistance Refer to the service agency directory included with your unit. If you experience any problems with the installation or operation of your unit, contact your local Roundup Authorized Service Agency. Authorized Service Agency Name: Fill in the information below and have it handy when calling your authorized service agency for assistance. The serial number is on the specification plate located on the rear of the unit.
VERTICAL CONTACT TOASTER IMPORTANT SAFETY INFORMATION (continued) In addition to the warnings and cautions in this manual, use the following guidelines for safe operation of the unit. • The toaster should be grounded according to local electrical codes to prevent the possibility of electrical shock. It requires a grounded receptacle with separate electrical lines, protected by fuses or circuit breaker of the proper rating. • Read all instructions before using equipment. • Bread may burn.
VERTICAL CONTACT TOASTER SPECIFICATIONS Electrical Cord & Plug Configurations Electrical Ratings Model & Mfg. No. Volts Watts Amps Hz Commercial Cord VCT-20CS 9200560 280-240 3200-4257 15.4-17.3 50/60 H Harmonized Cord (H)C*** CEE 7/7, 16 Amp., 250 VAC (Assembly Only). VCT-25CF 9200620 120 1760 14.7 60 VCT-25CT 9200622 120 1760 14.7 60 VCT-25CF 9200624 120 1760 14.7 60 VCT-25CF 9200630 120 1760 14.7 60 VCT-25CV 9200626 208-240 2600-3460 12.5-14.
VERTICAL CONTACT TOASTER SPECIFICATIONS (continued) Dimensions 3/4" (19.1 mm) 20-5/16" (519.9 mm) 10-3/4 (273.1 mm) 23-1/4" (590.5 mm) 22 11/16 555.8 mm) 9-3/4" (247.6 mm) 14-5/8" (371.5 mm) 6 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER INSTALLATION Unpacking Conveyor Cover Assy. 1. Remove unit and all packing materials from shipping carton. 2. Open the large box. It should contain: • Bun chute (Figure 2) • Plastic bag containing the release sheet (Figure 4) Heat Shield 3. Remove all packing materials and protective coverings from the unit and parts. Yellow Support Rod NOTE: If any parts are missing or damaged, contact Antunes Technical Service IMMEDIATELY at 1-877-7854-392. Assembling the Unit 1.
VERTICAL CONTACT TOASTER INSTALLATION (continued) IMPORTANT: Make sure Heat Shield is activating the conveyor interlock switch (see Figure 4). The conveyors will not rotate unless the heat shield is in place and interlock switch is activated (depressed). Lay sheet on a flat surface NOTE: Check the release sheet to make sure it is not caught in the conveyor. Additional release sheets can be obtained through your authorized service agency under part no. 7000249 (3 pack) or 7000250 (10 pack).
VERTICAL CONTACT TOASTER OPERATION Operating Instructions 1. Set the Bun Thickness Adjustment Control knobs to the desired settings (Figure 6). The recommended setting is 6. Bun Thickness Adjustment Controls (see Figure 6) NOTE: After initial run of 4-6 buns, adjust controls according to the desired finished product. 3 THICKNESS THICKNESS 1 4 5 2. Turn the Rocker Switch (power On/Off) to ON (Figure 5). Hi-Limit Reset 6 5 2 1 6 1 = 1/2"(12.7mm) 2 = 5/8"(15.9mm) 3 =11/16"(17.5mm) 4 = 3/4"(19.
VERTICAL CONTACT TOASTER MAINTENANCE WARNING Turn the unit off, disconnect the power source and allow the unit to cool down before performing any service or maintenance on the unit. Heat Shield Daily Release Sheet CLEANING THE ACCESSORIES 1. Turn the unit off, unplug the power cord, and allow the unit to cool for 30 minutes. Platen 2. Remove the Heat Shield and Bun Chute. Wash these items in soapy water, rinse with clear water, sanitize, and allow to air dry. Interlock Switch 3.
VERTICAL CONTACT TOASTER MAINTENANCE (continued) Conveyor Belt Chains MEASURING THE CONVEYOR BELT CHAINS Upper Yellow Support Rod Rotation 1. Facing the toaster, locate the approximate centerpoint of the Conveyor Chain. 2. Pull the Conveyor chain away from the edge of the toaster. Stand a U.S. Dime, 11/16” (1.8 cm) coin on end between the frame and the chain. If the gap is significantly wider than the coin, REMOVE links as described in the section titled Adjusting The Conveyor Belt Chains.
VERTICAL CONTACT TOASTER MAINTENANCE (continued) NOTE: Be sure sprocket setscrew is positioned on the flat of the gear reducer shaft. Maintain the 3/16” dimension as shown in Figure 11. Apply Loctite (Blue) to threads of setscrew and tighten securely. REPLACING CONVEYOR BELT CHAINS 1. Remove the old Conveyor Belt chain as described previously on page 10. 2. Place the replacement Conveyor Belt Chain on the top sprockets. Check for correct positioning (Figure 8). 7.
VERTICAL CONTACT TOASTER TROUBLESHOOTING WARNING To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equipment should be performed by qualified service personnel. The unit should be unplugged when servicing, except when electrical tests are required. Use extreme care during electrical circuit tests. Live circuits will be exposed. Problem No heat and conveyor belts do not move. No heat and conveyor belts move.
VERTICAL CONTACT TOASTER TROUBLESHOOTING (continued) Problem Platen is hot and the Conveyor Belt chains are not rotating. Possible Cause Corrective Action Toaster is installed incorrectly. Refer to the Installation and Operation sections of this manual for proper installation and operating procedures. Wiring problems. Check all electrical connections for burns, discoloration or arcing. Replace all connections or components with damaged terminals.
VERTICAL CONTACT TOASTER TROUBLESHOOTING (continued) Problem Possible Cause Product is over-toast- Temperature set too high. ed, Platen heat is too Bun Thickness Adjustment high, or drop time is Control knobs set incorrectly. too slow Buns sticking on Release Sheet. Corrective Action Set temperature control at a lower setting. Measure bun thickness and set bun adjustment controls correctly (Fig. 6, page 9). Clean or replace the Release Sheet or conveyor belt wrap. Conveyor Covers not installed.
VERTICAL CONTACT TOASTER TROUBLESHOOTING(continued) Problem Product is over-toasted or platen heat is too high or drop time is too slow. (continued). Possible Cause Corrective Action Spring tensioner assy(s). or tensioner bent or missing. Replace spring tensioner assy(s). (29, page 20) or tensioners (4, page 24) if damaged or loose. Replace slide rails (40, page 24) if worn or missing. Bun adjustment controls set incorrectly. Measure bun thickness and set bun adjustment controls correctly (page 9).
VERTICAL CONTACT TOASTER TROUBLESHOOTING (continued) Problem Product is getting stuck or conveyor belts stop when product is toasting (continued). Possible Cause Corrective Action Not enough voltage, defective Check receptacle for correct voltage. See power cord or rocker switch. Specifications (page 5). With unit plugged in and rocker switch on, check for correct voltage into rocker switch. If low or zero voltage, replace power cord. If voltage is correct, check for correct voltage out of rocker switch.
VERTICAL CONTACT TOASTER TROUBLESHOOTING (continued) Problem Conveyor belts are “jumping” or “snapping”. Possible Cause Corrective Action Toaster is installed incorrectly. Perform installation and operating procedures (pages 7-9). Bun adjustment controls set incorrectly. Measure bun thickness and set bun adjustment controls correctly (page 9). Conveyor drive motor inoperative or incorrect conveyor motor installed on toaster. To check drive motor: 1. Measure resistance of motor coil.
VERTICAL CONTACT TOASTER WIRING DIAGRAM Pictorial Wiring Diagram VCT-20 WIRING DIAGRAM NOTE: ALL WIRES TO BE 14 GA. AWM-105°C UNLESS OTHERWISE SPECIFIED. * 16 GA. TFE-200°C = 18 GA. AWM-105°C # 16 GA. AWM-105°C % 14 GA.
VERTICAL CONTACT TOASTER REPLACEMENT PARTS Parts Identification Interlock Switch Auxiliary Heater (VCT-20 only) Auxiliary Heater (VCT-20 only) Cover Plate (VCT-25 & VCT-50 only) Cover Plate (VCT-25 & VCT-50 only) Drive Chain Idler Sprocket Drive Sprocket Drive Sprocket Temperature Control Fan Blade Rocker Switch Hi-Limit Thermostat Drive Motor Assy. 20 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER REPLACEMENT PARTS (continued) Item Part No.
VERTICAL CONTACT TOASTER REPLACEMENT PARTS (continued) 22 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER REPLACEMENT PARTS (continued) 14 16 13 59 67 15 72 42 70 53 70 36 12 54 70 62 57 17 67 18 17 19 32 75 70 67 80 25 50 17 20 57 61 42 36 74 70 67 72 87 17 70 84 39 24 83 11 23 67 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER REPLACEMENT PARTS (continued) 16 15 52 13 70 1 14 37 5 4 67 34 41 79 78 7 6 7 88 51 4 31 1 27 85 76 40 2 67 49 30 9 41 26 67 89 76 90 65 6 7 68 24 83 P/N 1010729Rev. Rev.
VERTICAL CONTACT TOASTER OPTIONAL PARTS – VCT-25 & VCT-50 1 2 Item Part No. 1 2 7000236 7000238 Description Qty. Bun Feeder Butter Wheel Kit 1 1 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER NOTES 26 P/N 1010729 Rev.
VERTICAL CONTACT TOASTER NOTES P/N 1010729 Rev.
LIMITED WARRANTY Equipment manufactured by Roundup Food Equipment Division of A.J. Antunes & Co. has been constructed of the finest materials available and manufactured to high quality standards. These units are warranted to be free from electrical and mechanical defects for a period of one (1) year from date of purchase under normal use and service, and when installed in accordance with manufacturer’s recommendations.
