User manual

ManualsBrandsANYBUS ManualsRemote MaintenanceSerial device servers LAN, RS-232, RS-485 12 Vdc, 24 Vdc

Module Name Project No

AB7000 & AB7701

Document ID Revision

- 1.00

Issued by Date

Patrik Lansdorf 2005-11-28

Subject Approved by Page

Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 1(10)

About this application note:

This application note describes how to configure an

Anybus-X Serial Server together with an ABC-PDP

module. The contents describe step by step how to

setup the system.

This document assumes that the reader is familiar with

industrial communication, Profibus networks and HMS

Gateways.

ABC-PDP and ABX-Serial server

Application Note

Rev. 1.00

Summary of content (10 pages)

PAGE 1
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 1(10) ABC-PDP and ABX-Serial server Application Note Rev. 1.00 About this application note: This application note describes how to configure an Anybus-X Serial Server together with an ABC-PDP module. The contents describe step by step how to setup the system.
PAGE 2
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 2(10) History Revision Date Description Responsible 1.
PAGE 3
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 3(10) Contents 1 Requirements ............................................................................................................................................4 2 System configuration....................................................................................................
PAGE 4
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 4(10) 1 Requirements Description Name / Type Anybus Communicator for Profibus AB7000 / ABC-PDP Anybus-X Serial server AB7701 Power supply 24V DC N.a. Configuration cable for Anybus Communicator 017620 Serial/IP Com port redirection software 4.2.4 or later Anybus IPConfig utility 1.
PAGE 5
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 5(10) 2 System configuration Below you find an overview of the system configuration that is described in this document.
PAGE 6
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 6(10) 2.1 2.1.1 Software configuration Configuring the IP address on the Serial server After installing the Anybus IPconfig software and connecting the Serial Server to the network, it should be possible to see the module in the Anybus IPconfig tool, as shown below. Figure 2.
PAGE 7
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 7(10) 2.1.2 Configuring the Serial/IP After installing the software Serial_IP_Anybus-X_424b.exe, the following window will appear. Select which com. port to use, enter IP Address and Port number. Figure 4. Serial/IP Control Panel Under the Advanced button there are further settings to be made.
PAGE 8
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 8(10) The Nagle Algorithm has to be disabled, in order for the Serial Server to be able to work properly together with the Anybus Communicator. The settings of the Serial IP can always be accessed by right clicking on the Serial/IP, as shown below. Figure 6 Serial/IP Properties 2.1.
PAGE 9
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 9(10) 3 Testing Connect the Anybus Communicator to the Serial server with the configuration cable. Start up the ABC Config Tool and cancel the use of the wizard. Select which communication port to use, as shown in the picture below. Figure 9.
PAGE 10
Module Name Project No AB7000 & AB7701 Document ID Revision - 1.00 Issued by Date Patrik Lansdorf 2005-11-28 Subject Approved by Page Appl. note for ABC-PDP and Anybus-X Serial server Martin Falkman 10(10) More information about the network and products The latest manuals, software and GSD file can be found on the HMS homepage: www.anybus.com 4 List of Figures and Tables Figure 1. Hardware connection overview ..................................................................................