Instructions
Table Of Contents
- Anybus® Communicator™ - PROFIBUS to Modbus RTU/Serial
- Table of Contents
- 1. Preface
- 2. Safety
- 3. Preparation
- 4. About Anybus Communicator
- 5. Installation
- 6. Configuration Quick Guide
- 7. Communicator Configuration
- 7.1. Connect the Communicator
- 7.2. Access the Built-In Web Interface From HMS IPconfig
- 7.3. Access the Built-In Web Interface From a Web Browser
- 7.4. Communicator Built-In Web Interface Overview
- 7.5. General Subnetwork Settings
- 7.6. About Transaction Templates
- 7.7. Build Transaction Template
- 7.8. Nodes and Transactions
- 7.9. High Level Network Settings
- 7.10. I/O Data Map
- 7.11. Apply Configuration
- 7.12. To Use an Existing Configuration
- 7.13. To Use an Communicator Classic Configuration
- 8. PLC Configuration
- 9. Verify Operation
- 10. Use Cases
- 11. Maintenance
- 12. Troubleshooting
- 13. Technical Data
- 14. Reference Guides
Limit
NOTE
Limit can only be added as a Response frame eld.
• Name: You can name the Frame Field to make it easier to idenfy.
• Type: Specify the number of bytes in the frame. Select Byte (1 byte) (Default), Word (2 bytes), Double word (4
bytes).
• Endianess: Select Big-endian (Default) or Lile-endian.
• Min value: The lowest value of the limit range.
• Max value: The highest value of the limit range.
• Base number system: Select Decimal Dec (Default) or Hexadecimal Hex.
Data
• Name: You can name the Frame Field to make it easier to idenfy.
• Fixed eld*: Select Yes, set here (Default) or No, set when used.
• Length: Enter a value between 1 (Default) and 512 bytes.
• Min length: Specify the minimum length that can be set when the template is used.
• Max length: Specify the maximum length that can be set when the template is used.
• Default length: Specify the default length that can be set when the template is used.
Variable data
• Name: You can name the Frame Field to make it easier to idenfy.
• Fixed eld*: Select Yes, set here (Default) or No, set when used.
• Minimum payload length: Specify the minimum payload length that can be set when the template is used.
• Maximum payload length: Specify the maximum payload length that can be set when the template is used.
• Default max payload length: Specify the default payload length that can be set when the template is used.
• Data delimiter: Specify how to detect/dene the length of the variable data of the high level network. Select
Byte counter, End paern or None (Default).
For informaon about End- and Length character, see Data Delimiter and Subnet Delimiter Opons (page 62).
• Subnet delimiter: Specify how to detect/dene the length of the variable data of the serial subnetwork. Select
Byte counter, End paern or None (Default).
For informaon about End- and Length character, see Data Delimiter and Subnet Delimiter Opons (page 62).
• End paern: Specify the value dening the end of the payload, when a delimiter is set to end paern.
• Fill padding: Fill up unused data mapped to the high level network or the general area with a eld padding
value.
To deacvate/acvate Fill padding, click the slide toggle. When Fill padding is acvated, enter a Fill padding
value between 0 and 255.
• Base number system: Select Decimal Dec (Default) or Hexadecimal Hex.
Checksum
• Name: You can name the Frame Field to make it easier to idenfy.
• Checksum type: Specify the algorithm used to calculate the checksum. Select CRC (CRC-16-IBM) (Default), LRC
(ISO 1155:1978), XOR or ADD.
• Start oset: Specify the oset from where to start the checksum calculaon. Enter a value between 0 (Default)
and 511.
Build Transacon Template Anybus
®
Communicator
™
- PROFIBUS to Modbus RTU/Serial
SCM-1202-177 1.2 Page 61 of 134