www.anytone.net A1.
BT01 User Guide Bluetooth Microphone
Thank you for purchasing Anytone BT01 Bluetooth Microphone. This product uses a dedicated master-slave Bluetooth module to realize wireless talk and wireless operation settings for all functions of the AT-D578UV DMR mobile radio. Combined with the noise reduction function, it can effectively reduce background noise and ambient noise to achieve high-definition intercom. Precautions Please read the following regulations carefully before using this product.
APPLICABLE MODELS BT MODE CABLE MODE AT-D578UV/ AT-D578UVIII No GPS, No BT AT-D578UV PRO/ AT-D578UVIII PRO With GPS and BT AT-D578UV PLUS/ AT-D578UVIII PLUS With GPS and BT When you receive the BT01 microphone, please access the ATD578UV Menu-Setting-Device Info to check the version first, make sure the radio is upgraded to the latest version to get the BT-01 microphone working correctly. Latest firmware is available for download on https://www.anytone. net/download page. D578UV Ver1.17 V2.01.
1.Accessories Belt Clip WWZZ-0005 User's Manual 2.Charge The Battery Charging Instructions 1. Insert the USB plug of the charging cable into the power adapter. 2. Plug the power adapter into the AC power outlet. 3. Insert the other end of the charging cable into the charging/ upgrade interface of the radio. 4. The red charging indicator of the BT01 Bluetooth Microphone is on. 5. When the red charging indicator of the BT01 Bluetooth microphone goes out, the charging is complete.
3.
4.Basic Operation 4.1-Power ON Press the top [POW] button on microphone, the right green indicator light on, later the screen displays "Select Port", press choose the connect mode: or to BT MODE: Connect the BT01 microphone to AT-D578UV mobile radio through Bluetooth. CABLE MODE: Connect the BT01 microphone to AT-D578UV mobile radio through 4m cable. Click on "confirm" to select the connect mode. 4.
e.AT-D578UV radio displays "EXTERNAL BT MODE" on the screen, the pairing is done. BT01 microphone is able to access the radio menu and do communications now. » » Once the BT pairing is done, the BT microphone will automatically connect to AT-D578UV radio after reboot. 4.3-CABLE MODE connect to AT-D578UV After select "CABLE MODE" on microphone, it will display "NO DEVICE CONNECTED" when no radio is connected.
» » If the volume is adjusted to the maximum and you still consider it is not loud enough. » » In BT MODE, you can enter into Menu ->Bluetooth->RfBT SPK Gain to adjust the Bluetooth gain level and increase the volume. 4.6-Set Up VFO Frequency In Menu->Setting->Radio Set->Key Func, assign a key function to [VFO/MR]. Press the assigned [VFO/MR] key to switch the radio into VFO frequency mode, and then press the frequency.
channel switch speed is slow, it is difficult to improve due to the limitation of bluetooth communication. 4.8-Select a Zone Press the assigned [VFO/MR] key to switch the radio into channel mode first. Operation 1: Press the or Operation 2: Go to Menu Operation 3: In Menu key to change the zone. Zone, select a zone from the zone list. Setting Radio Set Key Func, assign a key function to [Zone Select]. Press the assigned [Zone Select] key, and input the zone number and confirm. 4.
4.12-Menu operation The menu operation on BT microphone is mapped from ATD578UV radio, the functions are fully same as AT-D578UV radio. Bluetooth menu function as below. BT Menu BT Pairing BT Names Paired Names BT RX Delay BT + int spk Sub menu Description -- Disconnects to the radio. -- The BT name of BT01 microphone. The BT name of BT device connected to the ATD578UV radio. The BT01 microphone disconnects to the radio at OFF once when signal drops.
BT Pin Code BT PTT Pair -- "Allows entry of BT Pin Code During Pairing. Majorly for the use of pairing to Car Audio System." PTT Pair Pair the small BP-02 BT PTT button. PTT Hold "ON:Click on BP-02 PTT button, the radio starts transmitting, click on the BP-02 PTT button again to end transmitting. OFF: Hold pressing BP-02 PTT button to transmit, release the button to end transmitting." PTT Name The BT name of BP-02 PTT button. "Infinity: The BP-02 PTT button will not go into dormant mode.
OFF Volt Tx Power TalkAround Reverse Digi Encrypt Call VFO / MR Scan AM air/FM Alarm Record Switch No Function Check the current battery capacity voltage Switch the power between super high, high, middle and low power. Switch between Talk Around and Repeater mode Turn on/off the frequency reverse function. Choose the digital encryption group for digital channel In Analog mode, send the DTMF/5TONE/2TONE encode. This function is only valid for analog channel. Switch between VFO mode and memory channel mode.
Priority Zone Program Scan Enhanced Sound LastCall Reply Switch ChType Ranging Roaming CH Ranging Max VOL Set Slot Set Aprs Type Zone Select Roaming Set Switch to Priority Zone "Press the key to start the scan in VFO channel scan start and end frequency must be programmed in CPS." In digital channel, switch the microphone tone to normal or enhanced mode. In digital channel, press the key to access the last call and press PTT to call back.
Enter into APRS menu quickly Switch the zone upwardly Switch the zone downwardly Set the voice come out from speaker on microphone Speaker Mode or radio. Switch between channel name display and Ch.Name frequency display for the current channel GPS On/Off Enable / disable the GPS. Enable / disable the CTCSS/DCS scanning for the analog channel.When the radio finds matched CTCSS/DCS for current channel, it will open the CDT Scan speaker and start receiving.
5.Technical Specifications GENERAL BT Mode BDR, EDR Protocol HFP; HSP; A2DP; AVRCP; SPP Transmit Distance 10 Meters Maximum Transmission Power 1.61dbm Sensitivity -80dBm Audio performance SBC Decoding Speaker 1W/8R LED Blue/Green/Red LCD screen 2.2inch Charge 5V Type C USB Battery capacity/Votage 1800mAh 3.7V Interface 3.
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
