ITEM: KF-AZ303** ANZZI SENSOR KITCHEN FAUCET & OPERATION MANUAL V1.
PRODUCT SIZE CHART 10.1" [258mm] 45° 8.4" [214mm] [1.3"~1.5"] 33~38mm MOUNTING HOLE 45° 12.3" [312mm] 8.2" [208mm] 7.1" [181mm] 2.6" [67mm] 10.6" [269mm] 21.7" [550mm] 2.9" [74mm] 1.2" [30mm] MAX:2.1" [54.0mm] 30" [762mm] 3/8" COMPRESSION TOOLS AND MATERIALS Wrench Marker Pen Screwdriver Drill Silicone Sealant 1/4" (6mm) Drill Bit Bucket PG.
COMPONENTS [01] [08] [02] [05] [06] [07] [03] [11] Outlet Hose [09] [04] Cable [10] Inlet Hose [12] [13] Sprayer Hose Part Discription [01] [02] [03] [04] [05] [06] [07] [08] [09] [10] [11] [12] [13] Faucet Flange Escutcheon Bracket Rubber Washer Metal Washer Nut Control Box Battery Box Screws & anchors Sticker Weight Allen Key Before installation: 1. Please check that all components are present. 2. Ensure that all supply lines are free of debris with supply stops installed. 3.
INSTALLATION 01 SINGLE HOLE STEP 1: Remove Rubber Washer [05], Metal Washer [06] and Nut [07] from Faucet [01] . Single hole application: Install Faucet [01] and Flange [02] through the faucet hole. Three holes application: Install Faucet [01] through Escutcheon [03] and Bracket [04] through the faucet hole. Adjust the Escutcheon [03]. Note: Faucet handle should always be on the right-hand side. THREE HOLES [03] [01] [02] [04] STEP 2: 2.
INSTALLATION 04 Line up the Arrows. Nut Line up the Grooves. Cable STEP 4: Connect the Faucet [01] 4-pin cable to the Control Box [08] cable. Secure the connection by tightening the nut found on the Control Box [08] cable. IMPORTANT! Make sure to line up the arrows and grooves found on both cables. Forcing a misaligned connection will damage the pins and cause the touchless sensor to malfunction.
INSTALLATION 06 [10] [09] [11] Bracket fig 1 fig 2 fig 3 STEP 6: 1. Install the Battery Box [09] to the bracket. 2. Connect the cable of the Battery Box [09] with the cable of the Control Box [08]. 3. There are two ways to secure the Battery Box [09] (fig 3): a. Secure the Battery Box [09] with Sticker [11] on the wall near the Control Box [08]. b. Locate the Battery Box [09] and mark the screw holes of the bracket on the wall. Drill two 0.24’’(6mm) diameter holes on the wall.
INSTALLATION 08 [12] STEP 8: Install the Weight [12]: 1. Slid the Weight [12] onto the sprayer hose above the bushing. 2. Push the Weight [12] downward to the bushing until it stops. 3. Shake the Weight [12] to make sure it is secured. Bushing 09 9.1 9.2 STEP 9: 9.1 Turn on hot and cold water supplies and check all connections at arrows for leaks. Retighten if necessary, but do not overtighten. 9.2 Open the handle and wave your hand over the sensor within 2.
OPERATION SPRAYER FUNCTIONS. The sprayer will be on flow mode when faucet is turned on. Press the button to switch to spray mode. The sprayer will switch back to flow mode automatically when the faucet is turned off. Button MANUAL OPERATION. 1. Using a Flathead screwdriver to turn the knob counter-clockwise until it stops to disable the sensor control and switch to a manually operated mode. In manual operation the water flow is fully controlled using the handle like any standard faucet. 2.
CLEANING & MAINTENANCE 1. To preserve the finish on the metallic parts of your ANZZI faucet, apply nonabrasive wax, such as car wax. Rinse off any cleaners immediately. 2. Clean the aerator regularly for calcium build-up or any blockage that reduces water flow. 3. If the water flows slower than normal, please clean the filter at the inlet hoses. a. Remove the hot and cold supply hoses (Fig 3.1). b.
