Full Product Manual

ManualsBrandsANZZI ManualsBath8 in. Widespread 2-Handle 3-Hole Bathroom Faucet with Pop-Up Drain in Matte Black and Brushed Gold

DON’T WAIT!

recognized as an

purchase and is for warranty

coverage.

in the registry card (Pg. 2) or register

at www.swcorp.com/register

LEAD FREE

NSF/ANSI/CAN 61

INSTALLATION & OPERATION MANUAL

V1.0

ITEM: L-AZ

902**

TONE LAVATORY FAUCET

10/30/2022

Summary of content (8 pages)

PAGE 1
ITEM: L-AZ 902** 2 TONE LAVATORY FAUCET INSTALLATION & OPERATION MANUAL V1.0 10/30/2022 LEAD FREE NSF/ANSI/CAN 61 DON’T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is recognized as an purchase and is for warranty coverage. in the registry card (Pg. 2) or register at www.swcorp.com/register.
PAGE 2
PAGE 3
PRODUCT SIZE CHART 5"-16" [127mm-406mm] 0.14" [3.5mm] 2.8" [71mm] 2.76" [70mm] 1.5" [38mm] 4.06" [103mm] 1.97" [50mm] 1.06-1.18" [27-30mm] 1.9" [48mm] 3.66" [93mm] 4.53" [115mm] 1/2" male thread connection 5.51" [140mm] 1.3-1.38" [33-35mm] TOOLS Wrench PG.1 Screwdriver 1.
PAGE 4
COMPONENTS [01] [03] [04] [06] [17] [02] [05] [18] [07] [08] [09] [10] [11] [12] [13] [14] [15] [16] Part. Description Qty [01] Spout 1 [02] Aerator 1 [03] Button 2 [04] Screw 2 [05] Key 1 [06] Handle 2 [07] Handle Base 2 [08] O-ring 3 [09] Valve Assembly 2 [10] Rubber Washer 2 [11] Metal Washer 2 [12] Lock Nut 2 [13] Rubber Gasket 1 [14] Metal Gasket 1 [15] Nut 1 [16] Hose 2 [17] Allen Key 1 [18] T-Wrench 1 Before installation: 1.
PAGE 5
INSTALLATION 1 [01] 2 [04] [17] [06] [03] [07] [08] Rod [01] [11] [16] Stem [08] [13] [14] red ring outlet [15] [09] [10] [11] [12] blue ring STEP 1: 1. Remove Rubber Gasket [13], Metal Gasket [14] and Lock Nut [15] from Spout [01]. 2. Install Hoses [16] to the screw holes at the bottom of the Spout [01] and tighten the Hoses [16] to secure. 3. Slide Hoses [16] through O-Ring [08], then install Spout [01] with O-Ring [08] in faucet hole. Adjust the Spout [01]. 4.
PAGE 6
INSTALLATION 3 4 inlet inlet hose or copper tube [16] outlet outlet HOT COLD STEP 3: STEP 4: Connect the Hoses [16] to the outlets of Valve Assembly [09]. Use hoses or copper tubes(NOT PROVIDED) to connect the inlets of Valve Assembly [09] and the Hot and Cold water supplies. Hand tighten the nuts and tighten with wrench to secure. 5 [06] [01] [02] [05] HOT COLD STEP 5: 1. Turn on hot and cold water supplies and turn the Handles [06], then check all connections at arrows for leaks.
PAGE 7
PUSH POP-UP INSTALLATION 6 Specification Body Gasket STEP 6: 1. Remove Body and Gasket from POP-UP drain. 2. Install the Body and Gasket through the drain hole of the sink as shown in Figure 6. 7 8 Body Washer Gasket Plastic washer Lock nut Outlet pipe STEP 7: STEP 8: Slide Washer, Plastic washer and Lock nut up onto the Body from under the sink and secure with Lock nut. Install the Outlet pipe with Gasket up onto the Body from under the sink and tighten it securely.
PAGE 8