ITEM: SB-AZ101C, SB-AZ101L SB-AZ101R, SB-AZ102C SB-AZ103C, SB-AZ103L SB-AZ103R ANZZI SHOWER BASE INSTALL & OPERATION MANUAL V1.0 DON’T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is recognized as an official purchase and is eligible for warranly coverage. Mail in the completed registry card (Pg. 2) or register online at www.swcorp.com/register.
PRODUCT REGISTRATION* IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2. Complete, cut-out and mail the registration card below.
INSTALLATION GUIDE BEFORE YOU BEGIN ● Prior to installation, examine all boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date. Please note that we will not replace any damaged products or missing parts free of charge after 10 business days or if the product has been installed.
TOOLS AND MATERIALS REQUIRED ar Mort Mortar Gloves Tape Measure Drop Cloth 1/4” Square Notched Trowel Level Pencil Sealant (2 tubes) Safety Glasses Square Caulk Gun Shims Hole Saw (sized to accomodate plumbing fixtures) SHOWER BASE CROSS SECTION DRAWING Waterproof Drywall 7/16” (11mm) minimum Finished Wall No Bedding Under Apron 4” (102mm) Bedding Material 2 1/8” (3mm) Bedding Material Area 5” (127mm) 2” (51mm) PVC Waste Pipe 2 × 4” Stud Wall (51 × 102mm)
PACKAGE CONTENTS PART A B DESCRIPTION QUANTITY Solid Surface Shower Base Stainless Steel Drain Cover 1 1 B A A B A B SHOWER FLOOR & DRAIN OPENING CONSTRUCTION DIMENSIONS ITEM: Nominal Sz. Dim. A Dim. B Dim. C Dim. D Dim. E 48" x 32" 48" x 32" 60" x 30" 60" x 30" 36" x 36" 48" x 32" 60" x 30" 48" 48" 60" 60" 36" 48" 60" 32" 32" 30" 30" 36" 32" 30" 4.375" 4.375" 43.625" 43.625" 8.48" 8.48" 18" 24" 30" 51.52" 51.52" 18" 24" 30" 15" 15" 14.07" 14.07" 15." 15.
INSTALLATION INSTRUCTIONS STEP 1 Ensure that the floor and the studs are at right angles. Provide a 6” Diameter recommented opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. ● Mark unit position on floor and through drain opening. ● These marks are used to verify base location after drain is installed.
STEP 3 ● Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). (Fig 3) ATTENTION ● Plumber’s putty will degrade base material, causing cracks and potential property damage. DO NOT use plumber’s putty to seal between drain and base. Use sealant or gasket. Fig. 3 1 STEP 4 ● Apply a generous amount of mortar that has been mixed to a thick consistency. Lower the shower base into position with the drain assembly sliding over the waste pipe.
STEP 6 Allow the mortar to completely harden before applying weight to the bottom of the shower base. ● Install the Drywall above the tile flanges and secure it to the studs. ● Put the tiles (or other finishing wall material) over the drywall leaving 1/8” gap between the bottom of the tile and the splash rim of the shower tray. Use caulk to fill that gap.
Care & Maintenance To ensure long lasting life for your shower base, wipe them off after each use with a soft cloth. To clean the shower base, use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.
