D D D C C C ANZZI GLASS SHOWER DOOR INSTALL GUIDE B B DRAWN Piyush CHECKED A Models: SD-AZ07-01,SD-AZ8073-01 SD-AZ09-01,SD-AZ8075-01 SD-AZ09-02,SD-AZ8075-02 B DRAWN Piyush 03-Mar-18 CHECKED TITLE QA A D SCALE 5 8 4 7 3 6 A APPROVED SIZE 6 TITLE MFG APPROVED 7 03-Mar-18 QA MFG 2 5 REV DWG NO 1/5 SHEET 1 1 OF 1 4 SIZE D SCALE REV DWG NO 1/5 1 OF 1 Have questions? Call us at 305-614-4070 or 3 2 email at info@anzzi.com.
GETTING STARTED Notice: This assembly requires two people due to the weight of the 4. Make sure the installation surface area is level, solid, and can support glass doors. Professional installers are highly recommended. the entire weight of the unit and the walls are plumb before beginning installation. Leveling adjustments and drilling may be necessary depend- 1. Carefully inspect all boxes and packages to make sure no damage ing on the unit being installed.
PARTS LIST 9 3 1 11 8 12 4 10 7 5 2 6 13 14 1. (1x) Glass door 2. (1x) Handle 3. (8x) Screw ST5×70 4. (2x) Hinge 5. (1x) Side strip 6. (1x) Bottom water proof strip 7. (1x) Bumper strip 8. (1x) Glass panel 9. (1x) Support bar 10. (2x) Wall anchor 11. (2x) Screw ST4.2×35 12. (1x) Silicone cleaner 13. (2x) Glass bottom protection seal 14. (1x) Decorative screw cover 15. (1x) Bottom bracket 16. (1x) Water proof strip for Door 17.
TUB DOOR DESIGN “A”: DETAIL A A OUTSIDE ATTENTION: This assembly portion only requires the parts from Diagram “A” for the assembly and installation of the Single Shower Door. Single Shower Door 23”-30” Diagram “A” is required for assembly 1. Secure the Hinges (05) to the Glass Door (01). Refer to Figure 1 for details. NOTICE: Do NOT place glass directly on a tile surface. To best protect the glass, ALWAYS lay the glass on a piece of cardboard or wood.
HINGES 3. Securely hold the glass door in place and mark drill holes on the wall for both Hinges (05). With holes marked, set the door aside and use a Ø ¼” drill bit to drill the holes in the wall. Gently set the Glass Door (01) back on the flat timber and adhere the hinges to the wall using two Countersunk Screws ST5x70 (04) on the hinge from the shower’s exterior.
GLASS DOOR 6. Obtain the following measurements: •Top edge of Glass Door (01) to the upper portion of the top Hinge (05) •Lower portion of the upper Hinge to the upper portion of the bottom Hinge •Lower portion of the bottom Hinge to 1/16” above the shower base. Use the above measurements to cut the Side strip (06). To cover the space to the wall, create a notch in the cut strip to allow them to slide into the Hinge. Take off the timber plate.
GLASS PANEL NOTICE: Doors wider than 30” will need an additional Stationary Glass Panel (11): See Design “B” for installation and assembly of Stationary Glass with Support Bar. DESIGN “B”: ATTENTION: This assembly portion only requires the parts from Diagram “B” for the assembly and installation of the Stationary Glass. Diagrams A and B are required for assembly of shower door with 6” small or 14”-30” large Stationary Glass. 21.
GLASS PANEL 22. Gently butt the vertical edge of the Stationary Glass (11) against the wall. 23. Securely hold the Stationary Glass (11) in place and close the Glass Door (01) while aligning it with the Stationary Glass. It may be necessary to adjust the position of the Anti-Water Strip (19) to ensure a tight fit with the top and bottom of the Glass Door. From the interior of the shower, precisely outline the placement of the Wall Brackets (24).
SUPPORT BAR MARK HERE DESIGN “B”: ATTENTION: This assembly portion only requires the parts from Diagram “B” for the assembly and installation of the Support Bar. NOTICE: The Support Bar* MUST be installed to allow for greater stability if the width of the Stationary Glass is 12” or greater. 27. Find the Support Bar* (12) and adjust it to an appropriate position on the glass and wall then level it horizontally.
MAINTENANCE Guarantee a longer life of the hardware finish by wiping off the metal parts with a soft cloth after each use. Avoid using abrasive cleaners and products especially those that contain bleach, acid, or ammonia. In the case that these chemicals are used, thoroughly rinse the surface as soon as possible and wipe dry with a soft cloth. Stainless-steel surfaces should be cleaned once a week or as needed. When applying a stainless-steel polish or cleaner, work with the grain and not against it.