Item: SD-FRLS05701** SD-FRLS05702** ANZZI GLASS SHOWER DOOR INSTALL & OPERATION MANUAL V2.1 DON’T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is recognized as an official purchase and is eligible for warranty coverage. Mail in the completed registry card (Pg. 2) or register online at www.swcorp.com/register .
PRODUCT REGISTRATION∗ IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULLY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. To ensure that your warranty is registered and confirmed please do one of the following: 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2. Complete, cut-out and mail the registration card below.
INSTALLATION GUIDE . . . . . BEFORE YOU BEGIN Please check the product for transit damage, missing parts immediately. Damage reported later cannot be accepted. Please handle the product with care. Avoiding any impact on all sides and edges of the glass. Consult your local plumbing codes prior to installation. To reduce the risk of breakage, keep corner protectors on glass while installing.
INSTALLATION GUIDE BEFORE YOU BEGIN . . . ATTENTION Threshold must be level for proper installation. The installation of this unit requires that you drill down into the threshold. Contact the manufacturer of the base, or threshold material with any questions regarding the drilling of holes into their product. This model requires a minimum 2-3/16"(55mm) of flat level threshold space for installation. Tools Required . This product is heavy and may require two people to install. .
PARTS [05] x1 [09] x1 [10] x1 [01] x1 [02] x1 [03] x1 [04] x1 [06] x1 [07] x1 [08A] x1 [08B] x1 [12] x2 [11] x1 3 [16A] x1 [16B] x1 [21] x1 [22] x6 [13] x2 [17] x1 [23] x1(2mm) [14] x2 [18] x1 [15A] x1 [19] x2(ST5x35 mm[1-3/8"]) [24] x1(3mm) [25] x1 [15B] x1 [20] x4(ST4x35 mm[1-3/8"])
ASSEMBLY [14] [03] [18] [02] [13] [08B] [07] [08A] [10] [22] [20] [19] [12] [09] [06] [01] [11] [17] [15B] [23] [24] [16B] [05] [21] [04] Part [01] [02] [03] [04] [05] [06] [07] [08] [09] [10] [11] [12] 4 Discription Qty.
6"[1930mm] 2"[50mm] 1.1"[29mm] 34"[865mm] 8.4"[214mm] SD-FRLS05701** 48"*76" 25.5"[648mm] 22.2"[563mm] 47.6"-48.
76"[1930mm] 2"[50mm] 1.1"[29mm] 34"[865mm] 8.4"[214mm] SD-FRLS05702** 60"*76" 31.5"[800mm] 28.1"[715mm] 59.6"-60.
. .. . ATTENTION To avoid personal injury or property damage, identify components and read all instructions before installing. This model requires a minimum 2-3/16"(55mm) of flat level threshold space for installation. (Dimension "D" of Fig 2.) The instructions below are for the option that fixed panel installed on the right. INSTALLATION INSTRUCTIONS Step 1 This shower door must be installed into a stud. Minimum threshold space is required.
Step 2 Remove Wall Jamb[021] and drill a 1/4" hole at each location marked for Wall Jamb[02] (Fig 3). ATTENTION Wear safety glasses and cut-resistant, non-slip gloves when drilling or cutting to avoid risk of injury. Fig3 Step 3 1.Insert Wall Plugs[22] in each hole location. 2.The Wall Plugs[22] should fit securely into the holes. If needed, a rubber mallet can be used to insert Wall Plugs. [22] 3.To reduce risk of property damage, the use of metal hammers is not recommended.
Step 4 Place the Wall Jamb [02] onto the wall. Use drill to start the ST4x35 screw [20] into the Wall Plugs [22] . Use a screwdriver to hand tighten until secure. (Fig. 5) [20] Fig5 Step 5 1.Carefully lay your glass panels flat on a soft, padded surface to inspect the glass. 2.Apply a good quality Silicone Sealant on the bottom of the Fixed Panel [10](Fig 6.1). 3.Place a thick bead of silicone along the full length of inside of back inner corner of Fixed Panel [10] Wall Jamb [02] (Fig 6.2). 4.
Step 6 1.Using a level, check that Fixed Panel [10] is vertical (Fig 7). 2. Install the Gasket [07]. (Fig 7.1) 1 [07] Fig7 Step 7 1.Check that the measurement from front of wall to Fixed Panel [10] is the same at one end and the other end of Fixed Panel [10] (Fig 8.1). 2.Use silicone caulk to seal the inner edge of the Fixed Panel [10] (Fig 8.2). Clean off any excess silicone.
Step 8 1.Measure the finished opening width at the model height("W1"). IMPORTANT: No need for cutting if the Support Bar[03] match the width. If they don’t, please see Step 2.2 for cutting instructions (Fig 9.1). 2.Using a pencil or another marking tool (such as masking tape), mark distance "W1, subtract 11/16"(17.5mm) " on the Support Bar[03] ( to leave some space for the Wall Bracket [18]). IMPORTANT: Double check the measurements before cutting.
Step 9 1.Unscrew screw "a" and tighten screw "b". Unscrew screw "c" and "d" until the screws not protrude from the inside surface. Keep the screws in the Wall Bracket [18] (Fig 10.1). 2.Install the Wall Bracket [18] to the Support Bar[03]. Slightly tighten the screw "d" (Fig 10.2). 3.Attach the Support Bar[03] to the inside of the Fixed Panel [10] with the Fasteners [13] as shown in Fig 10.3 . Ensure the Support Bar[03] is level. Use provided Allen wrench to hand tighten.
Step 10 1.Using a pencil or other marking tool (such as masking tape), mark the position of the Wall Bracket [18] (Fig 11.1). 2.Remove the Support Bar[03] and dissamble the Wall Bracket [18] from the Support Bar[03] . 3.Mark the screw hole locations (Fig 11.2). 4.Drill a 1/4" hole to accept the Wall plug [22] (Fig 11.3). IMPORTANT: To avoid risk of injury or product damage, make sure that you drill into studs. 5.Insert Wall plug [22] in hole location. If needed, a rubber mallet can be used to insert anchor.
Step 11 1.Disassemble the gasket and anchor from the Wall Bracket [18] . Attach the gasket and anchor to wall using Screw ST5x35[19] . Use drill to start screws into anchor. Next, use a screwdriver to hand tighten until secure (Fig 12.1). 2.Slide bracket sleeve onto end of Support Bar[03] (Fig 12.2). 3.Slide bracket sleeve onto the anchor. Tighten two screws of the Wall Bracket [18] by following sequence "b" , "a" (Fig 12.3). 4.
. Step 12 Depending on which side of the Fixed Panel [10] is installed, either Bottom Guide (L&R)[15] will be used.For this left side opening, Bottom Guide [15B] will be shown being installed. Mark center guide hole location. 1.Push the button of the Bottom Guide [15] to disassemble it into part a and b(Fig 13.1). 2.Place part a into correct position against the Fixed Panel [10] and mark the hole location (as shown in Fig 13.2). 3.
Step 13 1.Using provided adjustment Wrench[21], disassemble Trolley Wheel[12] as shown in (Fig 14.1). Repeat for the remaining Trolley Wheel[12] . 2.Install Trolley Wheel[12] to the Door Panel[09]. The washer should be on the metal part side(Fig 14.2). Adjust the Eccentric nut like the picture below(Fig 14.2a). 3.Use wrenches in the package to fix the Trolley Wheel[12] (Fig 14.3).
Step 14 1.From inside of enclosure, carefully, and with assistance from another capable person, hang sliding Door Panel[09] and Trolley Wheel[12] assemblies onto Support Bar[03] (Fig 15.1). 2.Disassemble Anti jump parts [14] as shown in Fig 15.2. 3.From inside enclosure, install Anti jump parts [14] to inside of sliding Door Panel[09] as shown in Fig 15.3. Use Wrench [21] and Allen Key 2mm [23] to hand tighten until secure. (Fig 15.3).
Step 15 1.Measure the distance between the Bottom Guide [15] and the door side wall ("W1").The length of Threshold Gasket [05] would be "W1,subtract 1-3/16"(30mm) "(Fig 16.1). IMPORTANT: No need for cutting if the Bottom Rail [04] and the Threshold Gasket [05] match the width. If they don’t, please see Step 2.2 for cutting instructions . 2.Using a pencil or another marking tool (such as masking tape), mark distance "W1 " on the Bottom Rail [04], "W1, 1-3/16"(30mm) "on the Threshold Gasket [05] .
Step 16 1. Check that the measurement from front of wall to Bottom Rail [04] is the same at one end and the other end of Bottom Rail [04] and mark using the pencil (Fig 17.1). 2.Install the Threshold Gasket [05] as shown in Fig 17.2. 3.Apply silicone to the Bottom Rail [04] and install it against the Bottom Guide [15] (Fig 17.3 and Fig 17.4). 4.Apply silicone to the Seal [16B] and attach to the end of Bottom Rail [04]. Make sure the Bottom Rail [04] align with the mark(Fig 17.5,Fiig 17.6).
Step 17 1. Attach the Magnetic gasket [06] to the Door Panel[09] close to the side wall as shown in Fig 18.1. 2.If the Side Gasket [08] is longer than the panels after installation. Cut the longer part. Cut the part of the Side Gasket [08] which interfering with the Support Bar[03] as shown in Fig 18.2.
Step 18 1. Attach the Magnetic wall column [01] to the installed Magnetic gasket [06] . Make sure the Magnetic wall column [01] align to the center of the door panel as shown in (Fig 19.1). 2.Slide the Door Panel[09] to the wall which in contact with the Magnetic wall column [01]. Using a pencil to mark the side of Magnetic wall column [01] (Fig 19.2). 3.Tear off the tape form the Magnetic wall column [01] (Fig 19.3).
Step 19 1. If needed, the door height at each wheel can be individually adjusted by using the Wrenches [21] . a. For the Trolley Wheel[12], using wrenches[21] in the package to carefully loose the nut for half turn. Rotate plastic nut as shown in Fig 20.1. This will raise or lower the Door Panel [09] at this location so that the door panel can match the wall better. Fasten the nut again after the adjustment. b.
Step 20 1. Disassemble Handle set[11] by loosing the screws(Fig 21.1). 2. Install handles and gaskets on two side of the Door Panel[09] as shown in Fig 21.2. The handle with screw holes face inside. 3. Tighten the screws to secure the Handle set[11]. IMPORTANT: DO NOT over tighten the screws. 1 2 gasket 3 gasket Fig21 Step 21 1. Apply a good quality Silicone Sealant on the walls and threshold along the bottom profile and wall profiles(Fig 22).
Step 22 1. For the Door Panel[09] on the left installation: Use Bottom Guide [15B] and Seal [16B] (Fig 23). 2. For the Door Panel[09] on the right installation: Use Bottom Guide [15A] and Seal [16A] (Fig 24).
Care & Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic bases and back walls (if installed): wipe them off after each use with a soft cloth. To clean the acrylic surface, use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
