ANZZI ® Item: SD-FRLS05901** SD-FRLS05902** ANZZI GLASS SHOWER DOOR INSTALL & OPERATION MANUAL V2.2 DON'T WAIT! REGISTER NOW! Register your product within 90 days to ensure your product is recognized as an official purchase and is eligible for warranty coverage. Mail in the completed registry card (Pg. 2) or register online at www.swcorp.com/register.
ANZZI ® PRODUCT REGISTRATION* IMPORTANT: YOUR WARRANTY WILL NOT BE RECOGNIZED UNLESS THIS CARD IS FULIY COMPLETED AND RETURNED OR ONLINE REGISTRATION IS COMPLETED. To ensure that your warranty is registered and confirmed please do one of the following: 1. Register online at www.swcorp.com/register. You will be asked to fill out the same information you would in the registration card. Registering online is fast, secure and ensures we receive your information. 2.
INSTALLATION GUIDE BEFORE YOU BEGIN • Please check the product for transit damage, missing parts immediately. Damage reported later cannot be accepted. Please handle the product with care. Avoiding any impact on all sides and edges of the glass. • Consult your local plumbing codes prior to installation. • To reduce the risk of breakage, keep corner protectors on glass while installing.
INSTALL ATION GUIDE BEFORE YOU BEGIN & ATTENTION • Threshold must be level for proper installation. • The installation of this unit requires that you drill down into the threshold. Contact the manufacturer of the base, or threshold material with any questions regarding the drilling of holes into their product. • This model requires a minimum 2-3/4"(70mm) of flat level threshold space for installation .4-1/8"(105mm) of flat level threshold space is better.
PARTS [OBA] x1 [088] x1 [09] x2 [01] x2 [02] x2 [03] x1 [04] x2 [05] x4 [06] x1 [07] x1 [lOA] x2 J �@ [14] x12 [15] x4(ST4x 35mm[l-3/8"]) �@ [20] x6(ST4x 35mm[l-3/8"]) 3 [11A] x2 [108] x2 [11B] x2 � [16] x2 [12] x2 � [17] x1 Q [21] x6 [22] x1(2.5mm) [23] x1 [13A] x1 0 [18] x1 [13B] x1 «immmmmw{] @ [19] x2(ST3.
ASSEMBLY [��!� ,.61 __ --�-=l o_2_1 --- F"""' 11 B] ""-"--.L.......111A] [12J---I --.1 =b:e: [13B1 08B] 01- [20] [21],______.,_---+-++--� <=> -t!) 01- => 01- => [09] CC> -t!) [18]-.. [19}--t l 06] [17]-� [14}--00 Part [O1] [02] [03] [04] [05] [06] [07] [08] [09] [1O] [11] 4 Discription Wall Jamb Support Bar Bottom Rail Gasket Side Gasket Threshold Gasket Sealing Strip Door panel Handle set Outer Wheels Inner Wheels Qty.
0 0 I 1.8"[45mm] E 0 ......... E E E 0 co 0 ("I') O') ........ -.:;I" ........ T""" T""" I'-- CX) T""" 0 E E T""" -.:;I" I'-- ........ N O') N E . .. E 47.6"-48"[1209-1219mm] 25.1 "[638mm] 3"[75mm] co �� ........ ("I') � ...... 5 25.1 "[638mm] I � .. .
0 0 I 1.8"[45mm] E 0 E E 0 co E 0 C") O') ........ -.:;I" T""" (0 T""" I'-- CX) T""" 0 E E T""" -.:;I" I'-- ........ N O') N 59.6"-60"[1514-1524mm] 31.1"[790mm] 3"[75mm] . .. E co -� ........ C") ...... 6 31.1"[790mm] I � ..
LL ATTENTION • To avoid personal injury or property damage, identify components and read all instructions before installing. • T his model requires a minimum 2-3/4"(70mm) of flat level threshold space for installation.4-1/8"(105mm) of flat level threshold space is better. (Dimension "D" of Fig 2.) INSTALLATION INSTRUCTIONS Step 1 • T his shower door must be installed into a stud. Minimum threshold space is required.
Step 2 OJ 1.Measure the finished opening width at the bottom("W2") and at the model height("W1"). IMPORTANT: No need for cutting if the Support Bar[02] and the Bottom Rail [03] match the width. If they don't, please see Step 2.2 for cutting instructions. 2.Using a pencil or another marking tool (such as masking tape), mark distance "W1, subtract 1-1/8"(28.
Step 3 1.Hold the Wall BracketAssembly[13A] in the designated position(left side) and mark the holes for drilling(Fig 5.1). Drill a 1 /4" hole at each location and insert the Wall Plugs[14](Fig 5.2,Fig 5.3). Attach the Wall BracketAssembly[13A] using the FH Screw ST4x35[15](Fig 5.4). 2.lnsert the SupportBar[02] into the installed Wall BracketAssembly[13A].Temporarily attach the remaining Wall BracketAssembly[13B] to the opposite end of the SupportBar[02]. Place a level on top of the SupportBar[02].
Step 4 1.Set the Bottom Rail [03] onto the threshold parallel with the outside edge. 2. Measure in 9/16"(14mm) min from the outside of the Wall to the Bottom Rail [03] and mark the position on the threshold(Fig 5). Or measure in 9/16"+ (A") if you want to install the shower door behind the outside of the wall. The measurement "A" must be the same in Step 1. 8 9/16"+(A") [03] x1 ' threshold ,,'' \' _____ -;1 , 9/16"+(A") Bottom Rail[03] wall Sections of Bottom Rail and threshold 10 Fig6
Step 5 1. Tear off the tape form the Bottom Rail [03] (Fig 7). Place the Bottom Rail [03] onto the marked position on the threshold(Fig 8). 2.Measure across the width of the threshold to locate and mark the center (Fig 9).
Step 6 1. Place the Bottom Guide[17] onto the center of the Bottom Rail [03] and mark the hole for drilling (Fig 10.1 and Fig 10.2). Drill a 1/8" hole at each marked location if drilling into acrylic or wood material (Fig 10.3). Drill a 1/4" hole at each marked location if drilling into tile material and insert the Wall Plugs[14] (Fig 10.4). 2.Fix the Bottom Guide[17] with screws ST3.5X25[19] (Fig 10.5). Install Bottom Guide Cap[18] to finish the Bottom Guide's installation (Fig 10.6).
Step 7 1.Apply silicone to the Seal [16] and attach to the end of Bottom Rail [03] ( Fig 11.1 and Fig 11.2). 2.Measure the length between the left side wall surface and the Bottom Guide[17] and the right side wall surface. 3.Cut the Threshold Gasket according to the length by a Tin snips. Cut the part of the Threshold Gasket[06] which interfering with the Seal [16] (Fig 11.3). The cut length would be the same as Seal [16] (Fig 11.4 ).
Step 8 Place Wall Jambs [01] into position by closing to Seal[16]. Ensure Wall Jambs[01] is vertical using a level. Temporarily tape fixed Wall Jamb[01] into position. (Fig 12) Wall Jamb Profile Figure Step 9 Using a pencil, mark location of all three screw holes for Wall Jambs[01 ].
Step 10 Remove Wall Jambs[01] and drill a 1/4" hole at each location marked for Wall Jamb[01] (Fig 14 ). & ATTENTION Wear safety glasses and cut-resistant, non-slip gloves when drilling or cutting to avoid risk of injury. Fig14 Step 11 1.lnsert Wall Plugs[14] in each hole location. 2.T he Wall Plugs[14] should fit securely into the holes. If needed, a rubber mallet can be used to insert Wall Plugs. 0 � 3.To reduce risk of property damage, the use of metal hammers is not recommended.
Step 12 1. Install Gaskets[04] to Wall Jambs[01] (Fig 16.1). Reposition Wall Jamb[01]. Use drill to start the ST4X35 screws[20] into the Wall Plugs[14]. 2.Next, use a screwdriver to hand tighten until secure(Fig 16.2).lnstall the Caps[21] to finished the installation(Fig 16.3). 3. If the Gaskets[04] is longer than the Wall Jambs[01] after installation. Cut the longer part(Fig 16.4 ).
Step 13 1.lnstall Support Bar [02] to Wall Bracket Assembly. The groove of the Support Bar [02] faces inward. Place a level to make sure the horizontal of the Support Bar [02]. 2.lf the Support Bar [02] isn't horizontal, remove the Support Bar [02] again. Find the higher Wall Bracket Assembly and loose the fixed screws for one turn.(Fig 17.1) 3.Turn the hex screw counter-clockwise for one turn each time. Replace the Support Bar [02] and level to check the horizontal.(Fig 17.2) 4.
Step 14 1.lnstall Inner Wheels[11A] to the Door Panel[OSB]. The washer should be on the metal part side(Fig 18.1). Adjust the Eccentric nut like the picture below(Fig 18.1a). 2.Use two wrenches[12] in the package to tighten the lnnerWheels[11A] (Fig 18.2). 3. Install the Sealing Strip [07] to the 4. Beware of the direction (Fig 18.3).
Step 15 1.Disassemble the hex screw and the anchor(Fig 19.1). 2.lnstall Outer Wheels [1 0A] to the Door Panel[0SA]. The washer should be on the metal part side(Fig 19.2). Adjust the Eccentric nut like the picture below(Fig 19.2a). 3. Use a wrench in the package and extra one to fix the Outer Wheels [1 0A](Fig 19.3).
Step 16 1. From inside the shower, hang the inside Door Panel [08B] first. Insert left wheel into the notch in the Support Bar[02]. Slide the door to the right and insert the other roller wheel into the second notch while inserting the Glass into the Bottom Guide[17] (Fig 20). 2. Next, from outside the shower, install the Outside Door Panel [08A] into the track on top of the Support Bar[02] and into the Bottom Guide[17] (Fig 21). 3.
1.A small piece cut on the flange of the two Side Gasket(see Fig22.1),it shows the cut size. Install them on the outside Door Panel [08A].Install the other two uncut Side Gaskets [05] to the inside Door Panels [08B].All the flanges of the Side Gasket should face towards inside. No need to cut the two gaskets for the inside glass panel 1-47/64"(44mm) 3-3/64" (77.
Step 18 1. Disassemble gaskets by removing handle levers and handle knobs(Fig 23.1). 2. Door Panel[OSA] installation: Install handles and two washers on the outer side of Door Panel[OSA]. Install gaskets and handle lever and handle knob on inner side of Door Panel[OSA]. Turn inner handle lever and handle knob to secure. (Fig 23.2) 3. Door Panel[OSB] installation: Install handles and two washers on the inner side of Door Panel[OSB].
Care & Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls (if installed): wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
ANZZI
