Install Instructions
Table Of Contents
- Safe Installation, Use and Service
- APPROVALS
- General Safety Information
- Introduction
- Features And Components
- Installation Considerations
- Installation Requirements
- Gas Supply Systems
- Supply Gas Regulator
- Power Supply
- Mixing Valves
- Dishwashing Machines
- Closed Water Systems
- Thermal Expansion
- Temperature-Pressure Relief Valve
- Condensate Drain
- Combustible Material Storage
- Contaminated Air
- Air Requirements
- Unconfined Space
- Confined Space
- Fresh Air Openings For Confined Spaces
- Outdoor Air Through Two Openings
- Outdoor Air Through One Opening
- Outdoor Air Through Two Horizontal Ducts
- Outdoor Air Through Two Vertical Ducts
- Air From Other Indoor Spaces
- Installation Requirements - Commonwealth of Massachusetts
- Venting Installation
- General Venting Information
- General Venting Instructions
- Intake Air Connection
- Venting Requirements
- Venting Installation Sequence
- Power Vent Installation
- Direct Vent Installation
- Vertical Termination Installation
- Sidewall Termination Installation
- Polypropylene Installations
- Al29-4C® Vent Installations
- Concentric Termination Installation
- 4 Inch Concentric Termination Installation
- Low Profile Vent installation
- Venting Arrangements
- Termination Clearances Sidewall Power Vent
- Termination Clearances Sidewall Direct Vent
- Water Heater Installation
- Temperature Regulation
- Control System Operation
- Start Up
- Troubleshooting
- Maintenance
- Diagrams
- notes
- notes
- notes
- Service Inquiries:
- Commercial
- Water Heater
- Limited Warranty
52
SERVICE CONTACT INFORMATION
The control system has a discrete menu that Installing contractors and/or service agents can access to enter contact information for
their customers. This contact information will be displayed with all Fault and Alert messages.
DESCRIPTION/ACTION DISPLAY
From the Desktop Screen (see Figure 59 on page 45) press
and hold down the middle (unmarked) Operational Button for 30
seconds and then release it.
This will launch a discrete menu where personalized contact
information can be entered.
Using the UP and DOWN buttons select (highlighted in black)
the "Show Contact Information" menu item.
Press the Operational Button under "CHANGE" to activate the
adjustment mode for this parameter.
Show Contact Information No
Change Contact Name
Change Contact Phone
Current Contact Info:
(000) 000-0000
Access Code
CHANGE BACK HELP
Service Contact Information
With the adjustment mode for "Show Contact Information"
activated the selection bar will change from a black ll to a
black outline.
Use the Up and Down Buttons to change the setting from
"No" to "Yes" and press the Operational Button underneath
"UPDATE" to save the new setting.
NOTE: The Access Code at the bottom of the Service Contact
Information screen is for manufacturing engineering purposes
only. There are no user settings or information accessed
through this menu item.
Show Contact Information Yes
Change Contact Name
Change Contact Phone
Current Contact Info:
(000) 000-0000
Access Code
UPDATE CANCEL
Service Contact Information
Using the UP and DOWN buttons select (highlighted in black)
the "Change Contact Name" menu item.
Press the Operational Button under "SELECT" to open the
Change Contact Name menu.
Show Contact Information Yes
Change Contact Name
Change Contact Phone
Current Contact Info:
(000) 000-0000
Access Code
SELECT BACK HELP
Service Contact Information
Follow the on screen instructions to enter your name or the
name of your company. There is a maximum of 20 character
spaces for this purpose.
When nished press the Operational Button "UPDATE" to save
the new Contact Name. The control system will return to the
discrete menu.
Enter the service contact below:
NAME: _
Use the > and < keys to move between
characters. Use the UP and DOWN keys to
change the character.
--
< > UPDATE
--
Using the UP and DOWN buttons select (highlighted in
black) the "Change Contact Phone" menu item and press the
Operational Button under "SELECT".
Follow the on screen instructions to enter a new Contact Phone
number and press the Operational Button under "UPDATE" to
save the new phone number.
When the new Contact Name and Contact Phone number
have both been updated, press the Operational Button under
"BACK" to return to the Desktop screen.
BACK HELP
Show Contact Information Yes
Change Contact Name
Change Contact Phone
Current Contact Info:
YOUR COMPANY NAME HERE
(123) 456-7890
Access Code
Service Contact Information