USER’S MANUAL A42W64AT4 Thank you very much for choosing the Envision Series Plasma TV. We recommend that you take a few minutes to read carefully through this manual before installing and using the TV.
CONTENT IMPORTANT SAFETY INSTRUCTIONS .................................................................................. ...1 Precautions and Reminders……………………………………………………………………………..2 Features and Function………………………………………………………….…………………….….4 Front Panel Control……………………………………………………………………………………….5 Basic Installation…………………………………………………………………………………………..6 Connection to other equipment………………………………………………………………………….7 Remote Control Function ...........................................................................
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read and follow all instructions. Do not operate this apparatus near water. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not block any of the ventilation openings. Clean only with a dry cloth. Do not defeat the safety purpose of the polarized or grounding-type plug. .
Precautions and Reminders 2 2 Do not place unit on uneven surfaces. Do not place the TV in confined spaces or in a box when using it. 3 3 3 Unplug immediately if there is any malfunction, Unplug immediately if other foreign materials like no video, no audio, smoke or a bad odor. are put inside TV box or if the TV fell down. 2 2 Do not throw any object like metals or flammable materials into the TV set.
Precautions and Reminders 2 2 DO NOT use liquid cleansers or aerosol Avoid direct sunlight, dusty, high humidity and cleansers to clean the plasma display. Dilute a smoky areas. neutral detergent with water and wipe with a soft cloth or gently clean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display. 3 3 Make sure to unplug the unit when not in use Call service personnel to clean the internal part for a long period of time (2 days). of the TV once a year.
Features and Function 42 inch(107cm)Large Screen Flat Panel Plasma Display Panel Resolution: WVGA 852 x 480 Pixels MAX Brightness of Panel: 1500 Cd/m2 MAX Contrast Ratio of Panel: 10000:1 View Angle: Greater than 160° Internal TV Tuner, Air:69 channels Cable:135 channels Frequency Range:55.25MHz to 859.
Front Panel Control - CH + - VOL + MENU MODE ⑦ ⑥ ⑤ ④ ③ ② ① ① MODE ② MENU Mode: Press to select input signal modes or use as Enter in Menu operation. ③- VOL + Left: Press to decrease the sound volume level or move Left in Menu operation. Right: Press to increase the sound volume level or move Right in Menu operation. ④ - CH + Down: Press to select the next lower Programme number or move Down in Menu operation.
Basic Installation 1. Connect TV Cable and Power Cord to this PDP TV Set. 2. Plug Power Cord to your home power outlet. 3. Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state. 4. Push POWER KEY on Remote Control or Power key on Front panel controls to switch the TV from stand by state to ON state. This TV will power on and you can see display on screen within a few minutes. 5.
Connection to other equipment Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on.
Connection to other equipment We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. The R / L is Audio input for every Y Cb Cr and Y Pb Pr. If your DVD or Set Top Box have Y Cb Cr or Y Pb Pr output, you can connect it to Y Cb Cr or Y Pb Pr input jack. And select to Y Cb Cr or Y Pb Pr source input. (Some DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output) Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup.
Remote Control Function “Wide Mode” Normal, Zoom ,Wide, Cinema display select “POWER” The TV Set turn on /turn off key Wide Mode “EPG” Display the state, source TV “TV” TV source select, into TV state “SLEEP ” Select timer into power down state. off→30→60→90→off “CC” To select close caption options (CC1,CC2……) “ENTER ” To enter sub Menu or sub item .
OSD Menu Descriptions Main Menu 1. Press “MENU” key on remote control or front panel controls to bring up Main Menu. 2. Press “ ” or “ ” to move the cursor up and down the sub menu list. 3. Press “ ” or “ ” to select sub menu item. 4. Press "Enter" to enter sub-item then use “ ” or “ ” to adjust. Setup Menu 1. Tuning Band: Select TV signal source between Air and Cable. Select Cable if you are connecting to a cable box and select Air if you are directly connecting to the antenna. 2.
OSD Menu Descriptions Video Menu . 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item. Contrast: Contrast adjustment, 0 ~ 100. Brightness: Brightness adjustment, 0 ~ 100. Color: Color chroma adjustment, 0 ~ 100. Tint: Tint adjustment, 0 ~ 100. Aspect Ratio: Aspect Ratio selection. Normal Zoom Wide Cinema.
OSD Menu Descriptions Feature Menu 1. Press “ ” or “ ” to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press “ ” or “ ” to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item. Time Set : The default time when you first set up theTV is 12:00 midnight. The internal clock starts from 12:00am. In the time set menu, first select the time zone you are in and manually change the time to the present time.
OSD Menu Descriptions Closed Captions section 1. Press “CC” key on remote control to select closed captions mode. NTSC TV: ATSC TV: Off..CC1 ..CC2 .. … Off ..CS1 ..CS2.. … 2. Select desired closed caption mode. 3.Closed captioning for analog NTSC channels is transmitted as CC1/CC2/CC3/CC4.Closed captioning for digital channels is transmitted as CS1/CS2/CS3 /CS4/CS5/CS6 or occasionally CC1/CC2/CC3/CC4. You need to select the option you want for analog channels and digital channels separately.
Specifications Item Panel Spec TV Mode Screen size Aspect Display pixels Effective display size Number of color Contrast Ratio Peak brightness TV Tuning Sound system 42 inch plasma display panel 16:9 852 x 480 (WVGA) 932mm x 532mm 16.
Troubleshooting Symptoms Checks Picture freezes in antenna mode. The TV does not react to remote controller commands. •Please ensure the antenna is properly connected. •Please switch off the mains and switch on again. •Re-install the channels if needed. Picture breaks up in DVI mode, especially when a set top box is connected. •The TV is trying to read the HDCP code sent by the set top box. •Please switch off the set top box and switch on again.
Troubleshooting Some parts of the screen do not light up After-images appear DVD The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma TV.
Envision Peripherals Inc. 47490 Seabridge Dr. Fremont, CA 94538 www.AOCdisplay.