User Guide

ManualsBrandsAOpen ManualsOtherAON101

Table of Contents

FULL PACKAGE CONTENT………………..2

INTRODUCTION....................................... 3

PRODUCT FEATURES ............................... 4

SOFTWARE DRIVER SUPPORT................... 5

INSTALLATION......................................... 6

HARDWARE INSTALLATION........................ 6

CONFIGURATION AND DIAGNOSTICS........... 6

RUNNING PLUG AND PLAY MODE........... 6

RUNNING JUMPERLESS MODE............... 7

RUNNING DIAGNOSTICS ....................... 7

DRIVER INSTALLATION.............................. 8

BOOT ROM INSTALLATION ....................... 8

SPECIFICATIONS................................... 10

Summary of content (10 pages)

PAGE 1
Table of Contents FULL PACKAGE CONTENT… … … … … … ..2 INTRODUCTION ....................................... 3 PRODUCT FEATURES ............................... 4 SOFTWARE DRIVER SUPPORT ................... 5 INSTALLATION......................................... 6 HARDWARE INSTALLATION ........................ 6 CONFIGURATION AND DIAGNOSTICS........... 6 RUNNING PLUG AND PLAY MODE ........... 6 RUNNING JUMPERLESS MODE ............... 7 RUNNING DIAGNOSTICS ....................... 7 DRIVER I NSTALLATION ........
PAGE 2
Full Package Content The adapter package should contain the following items: l One ISA PnP Ethernet adapter l User’ s guide l Driver diskette l One T-connector (for BNC port only) Please inform your reseller immediately should there be any incorrect, missing or damaged parts.
PAGE 3
Introduction This ISA PnP Ethernet adapter is high performance NE2000 compatible Ethernet adapter with Plugand-Play and full-duplex function The Plug-and-Play function can relieve the users from pains of taking care the adapter’ s resource configurations such as IRQ, I/O, and memory address, etc. The full-duplex function enables simultaneously transmission and reception on Twisted-Pair (10BASE-T) link to full-duplex Ethernet switching hub.
PAGE 4
Product Features l l l l l l l Compliant to IEEE 802.3 10BASE-2 and 10BASE-T standards. Supports Microsoft’ s Plug and Play configuration for jumperless mode. Supports Full-Duplex Ethernet function to double channel bandwidth. Automatic port selection between 10BASE-2 interface(BNC) and 10BASE-T interface(RJ-45) On-board socket for remote Boot ROM. On-board switch socket Plug and Play (PnP) or Jumperless (NE2000) mode. LED Indicators One LED on the bracket provides LINK indicators.
PAGE 5
Software Driver Support l Diagnostic Program l ODI Novell Client Dos and OS/2, Novell Client 32 for Dos, Netware Sever 3.x, 4.x, 5.0 l NDIS 2.x, 3.x, 4.x, 5.0 Windows 2000, Windows 98, Windows 95 OSR2, Windows 95, Windows NT, Microsoft WFW3.
PAGE 6
Installation Hardware Installation 1. 2. 3. Turn OFF the computer, unplug the power cord and open the computer case. Select an available ISA expansion slot and remove the expansion slot cover. Carefully insert the adapter into the slot until it is fully seated. Secure the adapter. Replace the computer cover and connect the network adapter. Reconnect the computer’ s power cord and plug it into the power outlet.
PAGE 7
95/98 system. The adapter default is NE2000 mode. For Plug and Play environment, please switch to PnP mode or execute SETUP.EXE choose the operating mode is PnP mode. Attach the cable and connector, it will automatic detect the medium type to use. • Running Jumperless (NE2000) mode Please switch to NE2000 mode and execute SETUP.EXE. A screen will guide you to configure the adapter to fit your computer system’ s environment. • Running Diagnostics You can select “Run Diagnostics” in SETUP.
PAGE 8
message is displayed at the bottom of screen. To press ESC to exit from the problem and power OFF, check hardware installation make the necessary changes, and then try again. If the diagnostic test still fails, contact your reseller for assistance. Driver Installation Before you connect adapter to the network, you have to install the network driver first. The adapter can work with all network drivers for Novell NE2000 adapter.
PAGE 9
discharge any static electricity on your body by touching a grounding surface such as the chassis of the PC. 1. 2. 3. Align the notch and pins of the ROM chip with notch and pinholes on the socket. Insert the Boot ROM into the socket on the adapter until it is firmly seated. Execute the SETUP.EXE file to enable the Boot ROM function by selecting the appropriate Boot ROM address from the setup menu.
PAGE 10
Specifications Standards Wiring connector Bus Interface I/O address IRQ Line Boot ROM address Operating Temperature Humidity Emissions IEEE802.3 10BASE-2, IEEE802.