User Guide

ManualsBrandsAOpen ManualsOtherAX4BRUG

PS/2 Mouse

Connector

SPP/EPP/ECP Parallel Port

LAN Ports

PS/2 Keyboard

Connector

USB Ports

COM 1 Port

VGA Port

SYSFAN1 Connecto

RAID IDE2 Connecto

Front Panel Connecto

FDD Connecto

USB Connecto

JP14 CMOS Clear Jum

4Mbit Flash ROM

Resetable Fuse

478-pin CPU socket with Voltage and

Frequency Auto-detection that supports

Intel

Pentium

4 1.4~2.8GHz+ CPU

32-bit PCI Expansion Slot x5

CPUFAN Connector

184-pin DIMM Socket x2 supports

PC-200/266 DDR SDRAM

maximum up to 2 GB

Intel

845E chipset

2200μF Low ESR Capacitors

TX Power Connecto

4-pin 12V. ATX Power Connector

COM2 Connecto

RAID IDE1 Connecto

WOL Connecto

TA/33/66/100 IDE Connector x2

SYSFAN2 Connector

(AOpen reserves the right to revise all

the specifications and information

contained in this documentation which

is subject to change without notice.)

Summary of content (8 pages)

PAGE 1
PS/2 Mouse Connector SPP/EPP/ECP Parallel Port (AOpen reserves the right to revise all the specifications and information contained in this documentation which is subject to change without notice.) PS/2 Keyboard Connector COM 1 Port VGA Port USB Ports LAN Ports 4-pin 12V.
PAGE 2
1. JP14 Clear CMOS You can clear CMOS to restore system default setting. To clear the CMOS, follow the procedure below. 1. Turn off the system and unplug the AC power. Everything you need to boot this motherboard is included in this Easy Installation Guide. For more information, a complete Online User's Manual can be found in the Bonus Pack CD. Thanks for the help of saving our earth. 2. Remove ATX power cable from connector PWR2. 3. Locate JP14 and short pins 2-3 for a few seconds. 4.
PAGE 3
. Installing Processor 5. Installing DIMM Module This socket supports Micro-FC-PGA2 package CPU, which is the latest CPU package developed by Intel. Other forms of CPU package are impossible to be fitted in. This motherboard has two 184-pin DDR DIMM sockets that allow you to install DDR200 or DDR266 memory up to 2GB. 1. Pull up the CPU socket lever and up to 90-degree angle. 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper interface. Match Pin 1 and cut edge.
PAGE 4
7. Support 2nd USB Port 9. Connecting WOL This motherboard provides four USB connectors to connect USB devices, such as mouse, keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You can use proper cable to connect the other USB connector to the back panel or front panel of chassis. To use Wake On LAN function, you must have a network card with chipset that supports this feature, and connect a cable from LAN card to motherboard WOL connector.
PAGE 5
13. PC99 Color Coded Back Panel 11. STBY LED STBY LED is AOpen’s considerate design that we aim at providing you friendly system information. The STBY LED will light up when power is provided to the motherboard. This is a convenient indication for you to check the system power status in many circumstances such as power on/off, stand-by mode and RAM power status during Suspend to RAM mode. The onboard I/O devices are PS/2 Keyboard, PS/2 Mouse, COM1, VGA port, Printer, USB, and LAN ports.
PAGE 6
15. Power-on and Load BIOS Setup Del After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press during POST (Power On Self Test). Choose "Load Setup Defaults" for recommended optimal performance. 17. Installing Intel IAA Driver You can install Intel IAA Driver to increase the performance of software applications and reduce PC boot times. You can find it in the AOpen Bonus Pack CD. 16. Installing Intel INF Utility 18.
PAGE 7
Part Number and Serial Number If you encounter any trouble to boot you system, follow the procedures accordingly to resolve the problem. The Part Number and Serial number are printed on bar code label. You can find this bar code label on the outside packing or on component side of PCB. For example: Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer. Part No. Serial No.
PAGE 8
1 Online Manual: Please check the manual carefully and make sure the jumper settings and installation procedure are correct. http://english.aopen.com.tw/tech/download/manual/default.htm Dear Customer, 2 Thanks for choosing AOpen products. To provide the best and fastest service to our customer is our first priority. However, we receive numerous emails and phone-calls worldwide everyday, it is very hard for us to serve everyone on time.