User Guide

ManualsBrandsAOpen ManualsOtherCRW620

INSTALLATION

1. Cautions During Installation

Caution: Dismantling the drive to attempt repairs or for other

reasons is dangerous because the laser may radiate outside

the unit. Do not disassemble the drive.

Caution:

q Install the drive in accordance with the specifications. Be

careful to avoid locations likely to cause vibration or

shock.

q Avoid locations where there is high humidity, much dust,

or poor ventilation.

q Avoid locations in direct sunlight, with severe changes in

humidity, or places where there are extremely high or

low temperatures.

q Don' t use the drive near radio or television receivers. It

may interfere with their reception.

2. Cautions During Use

Caution:

q Don’t suddenly move the drive from a cold place to a

warm one, or suddenly raise the room temperature.

Condensation may occur, causing abnormal operation.

q Make sure to remove the disc before moving the drive.

The disc may be damaged, causing data loss.

q Be careful to prevent foreign objects such as liquids or

metal from entering the drive. Should by chance a

foreign object enter the drive, please consult the dealer

where the drive was purchased.

q Don' t use benzene or thinner to clean dirt from the

drive. Don't allow chemicals such as insecticides to

contact the drive. Use a soft cloth to wipe the drive, or

Summary of content (13 pages)

PAGE 1
INSTALLATION 1. Cautions During Installation Caution: Dismantling the drive to attempt repairs or for other reasons is dangerous because the laser may radiate outside the unit. Do not disassemble the drive. Caution: q Install the drive in accordance with the specifications. Be careful to avoid locations likely to cause vibration or shock. q Avoid locations where there is high humidity, much dust, or poor ventilation.
PAGE 2
q q q q q q q moisten a cloth with neutral detergent diluted with water and use it to clean particularly dirty areas. Don' t cutoff the electric power while the drive is operating. When connecting the SCSI cable, observe the following points. If two different devices with the same SCSI ID are connected to the SCSI bus, the system may fail to function. Be careful that none of the SCSI Ids are the same when installing the equipment. Keep the total length of the SCSI cable within 6 meters.
PAGE 3
4. Other Cautions Caution: q When moving the equipment, make sure that the disc has been removed from the drive. q When not using the drive for a long period, dust may adhere to the disc tray. Before using the drive again, use dry air cleaner to remove the dust from the tray. q When connecting connectors, make sure that the power is OFF. If the power is ON, there is a possibility of short circuit. 5.
PAGE 4
Load the disc by pressing the eject button or by lightly pushing in the disc tray. Fig. 1-1 Load the disc Disc ejection 1. Press the eject button. 2. Slowly take the disc out of the disc tray. 3. Press the eject button or push the disc tray and the tray will be brought back into the drive. Caution: q After ejecting the disc, return the tray inside the unit quickly. When the tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure.
PAGE 5
6. Emergency Eject This drive has a function that allows the CD to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Follow the following procedures in such a case. 1. Turn the power to OFF. 2. Pinch the disc tray door between the fingers, and slowly pull it straight out.
PAGE 6
Caution: q Don' t use this feature except in an emergency. This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Fig.
PAGE 7
CONSTRUCTION AND INSTALLATION 1. Basic Construction The Compact Disc Rewriter Drive: The Rewriter consists of following parts. The Compact Disc Rewriter Drive's configuration, and Connector are shown below. Fig.
PAGE 8
2. Appearance Dimensions: Weight: 146.0 mm x 203.0 mm x 41.5 mm (Width) (Depth) (Height) 1.5 kg or less 3. Connector The Connectors are located as shown below. The function of each parts are also described below. Fig. 2-2 Front Fig.
PAGE 9
3.1 Disc Tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the CD will be loaded. Caution: Don' t use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 3.2 Eject Button This is the button used to eject or bring in the disc tray. 3.3 PowerI Busy Indicator This indicator light shines green when power is on.
PAGE 10
Caution: Be careful not to reverse the poser connector when attaching it. A reversed connection may cause damage to the equipment (not covered by the warranty). 3.7 SCSI connector Use a 50 pin double-end flat SCSI cable to connect to the SCSI interface. Caution: Connecting or disconnecting connectors while power is on may result in a short circuit, causing damage to the equipment. When connecting or disconnecting connectors, make sure to turn off the power beforehand. 3.
PAGE 11
Reserved Reserved Reserved Reserved SCSI ID Reserved Fig. 2-4 SCSI ID Jumper The SCSI ID Jumper will be set to all OFF (Open) as factory setting.
PAGE 12
Table 2-2 SCSI ID SCSI ID Pin No. 2 Pin No. 3 Pin No. 4 Remark 0 OFF OFF OFF Factory setting 1 ON OFF OFF 2 OFF ON OFF 3 ON ON OFF 4 OFF OFF ON 5 ON OFF ON 6 OFF ON ON 7 ON ON ON *1 Note ON : Jumper Pin is attached OFF: Jumper Pin is not attached *1: Don' t use this setting. It is located as the setting for SCSI Adapter Card usually. 4. Installation This drive is for setting horizontally.
PAGE 13
Horizontal Fig.