User Guide
Table Of Contents
- MX4GR
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- JP14 Clear CMOS Data
- CPU Installation
- CPU Jumper-less Design
- Full-range Auto-Detect CPU Core Voltage
- CPU and System Fan Connector (with H/W Monitoring)
- JP28 Keyboard/Mouse Wake-up Enable/Disable Jumper
- DIMM Sockets
- Front Panel Connector
- ATX Power Connector
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- S/PDIF (Sony/Philips Digital Interface) Connector
- AGP (Accelerated Graphic Port) Expansion Slot
- AGP Protection Technology
- ADD Card (Intel 845G chipset supported)
- WOM (Zero Voltage Wake on Modem) Connector
- WOM by External BOX Modem
- WOM by Internal Modem Card
- WOL (Wake on LAN)
- CNR (Communication and Network Riser) Expansion Slot
- PC99 Color Coded Back Panel
- Support 10/100 Mbps LAN onboard
- Support 2nd and 3rd USB2.0 Ports
- Chassis Intrusion Connector
- CD Audio Connector
- AUX-IN Connector
- Front Audio Connector
- Battery-less and Long Life Design
- CPU Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- 2200μF Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Enlarged Aluminum Heatsink
- Driver and Utility
- Auto-run Menu from Bonus CD Disc
- Installing IntelR Chipset Software Installation Utility
- Intel Brookdale-G VGA driver
- Installing Intel IAA Driver
- Installing Onboard Sound Driver
- Installing LAN Driver
- Installing USB2.0 Driver
- Installing Hardware Monitoring Utility
- ACPI Suspend to Hard Drive
- ACPI Suspend to RAM (STR)
- Phoenix-AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- AOpen Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- ATA/133
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- 102-108.pdf
- MX46LS
- Hardware Installation
- About “Optional” and “Upgrade Optional”…
- JP14 Clear CMOS Data
- CPU Installation
- CPU Jumper-less Design
- CPU and System Fan Connector (with H/W Monitoring)
- JP28 USB Keyboard / Mouse Wakeup
- DIMM Sockets
- Front Panel Connector
- ATX Power Connector
- AC Power Auto Recovery
- IDE and Floppy Connector
- IrDA Connector
- AGP (Accelerated Graphic Port) Expansion Slot
- WOM (Zero Voltage Wake on Modem) Connector
- WOM by External BOX Modem
- WOM by Internal Modem Card
- WOL (Wake on LAN)
- Support 10/100 Mbps LAN onboard
- CNR (Communication and Network Riser) Expansion Slot
- PC99 Color Coded Back Panel
- Support 3 USB Ports
- CD Audio Connector
- Modem Audio Connector
- Front Audio Connector
- Dr. LED Connector (Upgrade Optional)
- Battery-less and Long Life Design
- Over-current Protection
- Hardware Monitoring
- Resettable Fuse
- 1500μF Low ESR Capacitor
- Layout (Frequency Isolation Wall)
- Pure Aluminum Heatsink
- Driver and Utility
- AWARD BIOS
- Overclocking
- Glossary
- AC97
- ACPI (Advanced Configuration & Power Interface)
- AGP (Accelerated Graphic Port)
- AMR (Audio/Modem Riser)
- Bonus Pack CD
- APM (Advanced Power Management)
- ATA (AT Attachment)
- ATA/66
- ATA/100
- BIOS (Basic Input/Output System)
- Bus Master IDE (DMA mode)
- CNR (Communication and Networking Riser)
- CODEC (Coding and Decoding)
- DDR (Double Data Rated) SDRAM
- DIMM (Dual In Line Memory Module)
- DMA (Direct Memory Access)
- ECC (Error Checking and Correction)
- EDO (Extended Data Output) Memory
- EEPROM (Electronic Erasable Programmable ROM)
- EPROM (Erasable Programmable ROM)
- EV6 Bus
- FCC DoC (Declaration of Conformity)
- FC-PGA (Flip Chip-Pin Grid Array)
- Flash ROM
- FSB (Front Side Bus) Clock
- I2C Bus
- IEEE 1394
- Parity Bit
- PBSRAM (Pipelined Burst SRAM)
- PC-100 DIMM
- PC-133 DIMM
- PC-1600 or PC-2100 DDR DRAM
- PCI (Peripheral Component Interface) Bus
- PDF Format
- PnP (Plug and Play)
- POST (Power-On Self Test)
- RDRAM (Rambus DRAM)
- RIMM (Rambus Inline Memory Module)
- SDRAM (Synchronous DRAM)
- Shadow E2PROM
- SIMM (Single In Line Memory Module)
- SMBus (System Management Bus)
- SPD (Serial Presence Detect)
- Ultra DMA
- USB (Universal Serial Bus)
- VCM (Virtual Channel Memory)
- ZIP file
- Troubleshooting
- Technical Support
- Product Registration
- How to Contact Us

M
M
X
X
4
4
G
G
R
R
O
O
n
n
l
l
i
i
n
n
e
e
M
M
a
a
n
n
u
u
a
a
l
l
A
A
O
O
p
p
e
e
n
n
“
“
W
W
a
a
t
t
c
c
h
h
D
D
o
o
g
g
T
T
i
i
m
m
e
e
r
r
”
”
With this motherboard, AOpen provides a very special, useful feature for overclockers. When you power-on the system, the
BIOS will check last system POST
status. If it succeeded, the BIOS will enable “Watch Dog Timer” function immediately, and set
the CPU FSB
frequency by user’s setting that stored in the BIOS. If system failed in BIOS POST, the “Watch Dog Timer” will
reset the system to reboot in five seconds. Then, BIOS will detect the CPU’s default frequency and POST again. With this
special feature, you can easily overclock your system to get higher system performance, and without removing the cover of
system housing to set the jumper to clear CMOS data when your system hanged.
BIOS
Clock Generator
CPU
AOpen
Watch Dog
Timer
Countdown about
5 seconds if fails
in POST
Reset Signal
Enable/Disable Signal
from BIOS
CPU ID Signal
26