System FLASH BIOS RJ45 Jack RJ45 Jack FAN4 Connector VGA Connector System FAN JP5 VGA IRQ Jumper Low ESR Capacitors VIA VT82C686B (SB) IPMI ROM FAN1 Connector System FAN JP3 CMOS Clear Jump 370-pin CPU Socket with Voltage & Frequency Auto-detection ® supports Intel Pentium™ III (Both Coppermine & Tualatin are supported) 168-pin DIMM Socket x 3 supports PC133 SDRAM maximum up to 3 GB 32 Bit PCI Slot x 2 ATX 20-pin Power Connector Power supply Fan Sensor FAN3 Connector VIA 694T (NB) CPU FAN x 2 100W PF
1. JP3 Clear CMOS You can clear CMOS to restore system default setting. To clear the CMOS, follow the procedure below. 1. Turn off the system and unplug the AC power. 2. Remove ATX power cable. Everything you need to boot this motherboard is included in this Easy Installation Guide. For more information, a complete Online User's Manual can be found in the Bonus Pack CD Disc. Thanks for the help of saving our earth. 3. Locate JP3 and short pins 2-3 for a few seconds. 4.
. Installing Processor 5. Setting CPU Voltage & Frequency 1. Pull up the CPU socket lever and up to 90-degree angle. Setting CPU Core Voltage This motherboard supports CPU VID function. The CPU core voltage will be automatically detected and the range is from 1.05V to 1.825V. It is not necessary to set CPU Core Voltage 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper interface. Match Pin 1 and cut edge. Then insert the CPU into the socket.
6. JP2 IDE RAID / ATA Controller Jumper This jumper allows you to decide the system to support IDE RAID or ATA interface. The default setting is IDE RAID. 1 IDE RAID (default) 8.JP5 VGA IRQ Jumper This jumper allows you to enable or disable VGA sending IRQ to the system. The default setting is Disable. 1 1 1 ATA 7. JP4 Intrusion Alarm Cable The system is equipped with an intrusion alarm device.
10. JP11 BIOS Restore Function This jumper allows you to enable or disable the BIOS restore function. The default setting is Disable. 12. Connecting ATX Power Connector The ATX power supply uses 20-pin connector shown below. The connector is equipped with a foolproof device. Make sure you plug in the right direction. +3.3V +3.3V -12V +3.3V COM COM PS-ON 1 Disable (default) 1 COM COM +5V COM COM Enable 11.
14. Support 10/100 Mbps LAN Onboard On the strength of Intel 82550 PHY on board, which is a highly-integrated Platform LAN Connect device, it provides 10/100M bps Ethernet for office and home use, the Ethernet RJ45 connector is located on the back panel. The green LED indicates the link mode, it lights when linking to network and blinking when transferring data. The orange LED indicates the transfer mode, and it lights when data is transferring in 100Mbps mode.
18. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press during POST (Power On Self Test). Choose "Load Default Setting" for recommended optimal performance. If you encounter any trouble to boot you system, follow the procedures accordingly to resolve the problem. Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer.
1 Online Manual: Please check the manual carefully and make sure the jumper settings and installation procedure are correct. http://www.aopen.com/tech/download/manual/default.htm Dear Customer, 2 Thanks for choosing AOpen products. To provide the best and fastest service to our customer is our first priority. However, we receive numerous emails and phone-calls worldwide everyday, it is very hard for us to serve everyone on time.
