User manual

6
CHARGING WITH THE MAINS POWER PACK
Plug the mains power pack (13) connection into the DC connection (4) of the power pack, then plug the mains plug into the 230 V socket.
The blue battery state-of-charge display (2) lights up partly, one LED is always flashing and thus shows the current charge condition.
Charge the mini lithium power pack until all LEDs in the battery state-of-charge display are continuously lit. The mains adaptor can now be
unplugged from the power pack and from the 230 V socket. For a maximum battery service life, the starting aid should be recharged every
time it is used and topped up at least every three months.
CHARGING WITH THE 12 VOLT ADAPTOR
Plug the 12 V adaptor (12) into the DC connection (4) of the power pack, connecting the 12 V connection with the cigarette lighter
connection in your car.
After this, the power pack behaves exactly the same as when it is being charged with the mains adaptor. The speed of charging however
can vary according to whether the car engine is running, the condition of the car battery, etc.
STARTING AID
Before connecting the starting aid to the battery ALWAYS carry out the following checks:
• make sure that the car ignition and all accessories – lights, radio etc. – are switched off.
• make sure that the car battery is a 12 V battery and that it is undamaged.
• make sure that the battery terminals are clean and that the connections are firmly screwed in place.
1. Before attaching the starting aid cable, switch off the car ignition.
2. Take care that the red positive (+) terminal clamp and the black negative (-) clamp do not come into contact.
3. Make sure that the entire area is well ventilated.
Important: in this phase the starting aid cable (9) is not yet connected to the power pack.
4. First attach the red positive (+) terminal clamp to the positive (+) battery connection. The terminal clamp and the lead must not be
permitted to touch any moving parts or petrol lines.
5. Connect the black negative (-) terminal clamp to the negative (-) battery terminal.
6. Now connect the starting aid cable (9) to the power pack, opening the cover of the starting aid connection (8).
7. Turn the ignition key and hold it "on" for six seconds as a maximum; the car should start. If the motor fails to start after a few
seconds, turn the ignition off and then wait for at least three minutes before trying again.
8. When the motor has started, remove the starting aid cable from the power pack.
9. Then remove the black, negative (-) terminal clamp first from the car battery, then the red positive (+) terminal clamp.
10. After use, pack the cable and the power pack carefully, closing the cover of the starting aid connection.
11. After use, recharge the starting aid as described under CHARGING.
12. Check the state of charge of the battery regularly by pressing the Activation button.
WARNING: STARTING WITH THE STARTING AID MAY CAUSE DAMAGE TO ELECTRONIC COMPONENTS. ALWAYS CONSULT
THE CAR MANUFACTURER'S HANDBOOK TO DETERMINE WHAT SAFETY PRECAUTIONS IT MAY BE NECESSARY TO TAKE.
LED WORKING LAMP
To operate the LED working lamp, first activate the appliance by pressing the activation button (1). The power pack lights up and shows the
current state of charge. Now press the activation button again and keep it pressed for a few seconds.
- As soon as the LED lights up, you can release the button.
The working lamp has two further lighting modes. A short press on the activation button switches it into mode 2, when it flashes quickly. With
a further short press on the button, you switch into mode 3. The lamp now blinks briefly and quickly alternately.
With a further short press on the button, the lamp is switched off.
A few minutes after you finish using the lamp, the power pack switches itself off automatically.
USB CONNECTION and 12 V/19 V CONNECTION
To operate the USB connection, activate the appliance first using the activation button (1). Then you can use the USB connection (3) in the
usual way. Use either the adaptor supplied or the adaptor which belongs to your mobile phone/smart phone/tablet/etc.
A few minutes after you finish using the USB connection or the 12 V/19 V connection, the power pack switches itself off automatically.
STATE OF CHARGE
If the activation button is pressed, the battery charge state will be displayed. While being recharged, this is shown continuously.
If the state of charge of the power pack is too low, activation using the activation button is not possible. You must now recharge the power
pack.