MANUAL MA200CDR INFO@APART-AUDIO.
Safety First! • Read all documentation before operating your equipment. • Retain all documentation for future reference. • Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. • Do not spill water or other liquids into or on the unit. • Make sure power outlets conform to the power requirements listed on the back of the unit.
Content 1. APart MA200CDR Mixing Amplifier 2. Front Panel 3. Rear Panel 4.Tuner Controls 5. Inside Settings 6. Overview Of The MA200 Series 7. How To Deal With 100V Loudspeakers Systems 8. Technical Specifications 9. Block Diagram INFO@APART-AUDIO.
1. APart MA200CDR Mixing Amplifier The MA200CDR is a professional 4 zone PA mixing amplifier for commercial and industrial applications. Rarely seen on its competitors, all microphone inputs have integrated speech filters and they are high-class transistor-balanced type, allowing good control of hum and noise over long cables. He’s able to drive 8-ohm or constant-voltage loudspeaker lines (50-70-100V).
2. Front Panel 7 8 8 9 3 2 6 10 12 11 13 14 5 4 1 1) Power switch: Here you can switch the power on and off. 2) Overload indicator: This red LED illuminates when one of the protections have been activated. No or distorted sound will be heard. This will be in case of overheating, being the result of drawing too much power from your amplifier, or the impedance of the speaker lines connected are below the minimum load impedance (see17).
3. Rear Panel 15 16 17 18 19 21 22 24 25 26 26 27 20 23 34 35 33 32 28 27 30 28 31 27 29 36 15) Voltage selector. Set the local voltage: If any doubt, contact your dealer. The unit is shipped with the selector set to 230VAC. 16) Mains socket: The unit can be connected to the mains circuit by a standard IEC type power cord. This socket contains a 6,3AT, slow blow fuse. Use a screw driver to flip out the fuse compartment and to replace it by the same type.
24) CD stereo input, 500mV: Here you can feed a line level signal. You have to make your choice with the selector at the front (see 12). Stereo signals will be summed together. 25) AUX input, 500mV: Use this stereo RCA input to connect a line level source such as CD player, MD player, BGM computer, etc…. You have to make your choice with the selector at the front (see 12). Stereo signals will be summed together.
4. Tuner Controls RADIO AM / FM mode switch: Each time you press this button, the tuner will switch from FM to AM and the other way round. The actual radio band will be displayed at the left. Scan up / down: By pressing “UP” or “DOWN” a few seconds, the tuner will start to search the next/previous radio station with sufficient signal (auto scanning). By just pressing “UP” or “DOWN” you work in manual mode. Each time you press, you change the frequency by 50 kHz for FM and 9 kHz for AM.
5. Inside Settings Phantom Power MIC1 : JP3 MIC2 : JP4 MIC3 : JP5 MIC4 : JP11 JP3 JP4 JP5 JP11 Phantom on / off jumper The MA200CDR has been shipped with these jumpers in the OFF position. For each microphone input a jumper is available. When you put a jumper to the ON position, phantom power will be supplied to the microphone input involved so you can use condenser microphones. In this case NO unbalanced jacks should be used! Phantom power does not damage dynamic balanced microphones.
6. Overview Of The MA200 Series MA200CDR • High quality 200 Watts 100 Volt mixing amplifier • Integrated 2-tone chime (adjustable volume) • Integrated AM/FM tuner and CD/MP3 player • 4 output zones.
7. How To Deal With 100V Loudspeaker Systems In fact working with 100V loudspeakers is rather simple, when done in the right way. Each 100V loudspeaker has a 100V transformer which can be set to a certain power, for example: 1,5 3 or 6W. As the example shows, the sum of all loudspeaker settings should never exceed the amplifier’s power specifications. Never use low impedance (= 8 ohm) loudspeakers on a 100Volt system, not even one.
8. MA200CDR Block Diagram TRAFO Pre Amp 1V EMERGENCY TELEPHONE + VOX - PRIORITY SCREW4 CHIME DIN5 1.5mV JP3 MIC 1 PROTECT PHANTOM ON SIGNAL 100% LIMIT 24V/1A PRIORITY XLR3 3 Hi-Q Pre Amp 2 + - 1 POWER AMP + VOX + - TONE AUTO GAIN MASTER MUTE PreAmp OUT MUTE JP4 + - VOLUME INPUT1 SPEECH FILTER + - CONTROL PowerAmp IN 100V + 70V - 50V 8 ohm COM PHANTOM 1.5mV 3 MIC 2 MUTE Hi-Q Pre Amp 2 REQ OUT + - 1 VOLUME INPUT2 SPEECH FILTER JP5 PHANTOM 1.
9.
Inputs MIC InPut 1; ¼” tRS PhOnE jACk At thE fROnt XLR3 COMbO, DIn5; EuRO bLOCk SENSITIVITY 1,5 MV IMPEDANCE 600 Ω S/N (AT MAX. VOLUME) > 65 dB PHANTOM POWER 14 V (internal jumper) FREQUENCY RESPONSE > 80Hz->15Khz (+1/-3 dB) VOX MUTE trigger level 0,6 mV, 1Khz, mutes mic 2,3,4+music, > 40 dB Mic input 2,3 & 4: XLR3 balanced SENSITIVITY 1,5 mV IMPEDANCE 600 Ω S/N (AT MAX.
Outputs SPEAkER SELECtOR ZONE 1 3 on/off ZONE 4 paging on/off music on/off SPEAkER zOnE OutPut, EuRO bLOCk HIGH Z ZONE 1-2-3-4 100 V SPEAkER Out; EuRO bLOCk HIGH Z 50 (12,5 Ω) 70 (24,5 Ω) 100 V (50 Ω) LOW Z 8Ω PhAntOM POwER MIC 1-2-3-4 14 V; internal jumpers PRE AMP Out LEVEL 1V tunER (RCA MOnO)(MOh) LEVEL 300 mV RECORD Out; RCA MOnO LEVEL 1V PRIORItY Out LEVEL 24 V DC; max 1A, short circuit protected ChIME 2 tone activated by contact closure; euro block DIN5 on/off and level set by trim
AnY SuGGEStIOn? They are well appreciated and eventually rewarded! Send your ideas or suggestions to suggestions@apart-audio.com MA200CDR is developed by Audioprof nv Lanteernhofstraat 90 BE-2100 Deurne BELGIUM WWW.APART-AUDIO.
