Datasheet

ManualsBrandsAPC Manualselectrical equipment & suppliesAP95103202

APC MasterSwitch Power Receptacles (AP9510 Series)

Introduction APC

MasterSwitch™ Power Receptacles increase the maxi-

mum amperage controlled by a MasterSwitch unit. A North

American model of MasterSwitch can supply a maximum of

amps total over eight outlets. Using eight

5-15 Power Recepta-

cle units, for example, you can control power to a total load of

up to

96 amps—12 amps per receptacle—using a single

MasterSwitch. For international models, you can control power

to loads totaling

80 A—10 amps per receptacle—using a single

MasterSwitch unit.

You can mount up to three Power Receptacle units in a Power

Receptacle Tray (

AP9510BAY), which installs into an APC

NetShelter

enclosure. You can mix and match various Power

Receptacle models in the Power Receptacle Tray. The tray

requires

2U of space in the NetShelter and can fit conveniently

on the rear mounting flanges, behind a MasterSwitch unit.

Electrical

information

Mounting

options

Power Receptacles can be placed on a desk or mounted in a

rack. To place on a desk, attach the four rubber feet (supplied)

to the bottom of the unit. To mount in a rack, use the Power

Receptacle Tray (

AP9510BAY) and follow the mounting

instructions in “Mounting power receptacles in a rack” on

page 2.

APC

Part Number

Recep-

tacle

Volts Amps

Relay Coil

AP9510515

5-15

duplex

115 12

100/120 VAC

@ 17/24 mA

AP9510520

5-20

duplex

115 16

100/120 VAC

@ 17/24 mA

AP9510L620 L6-20

240 16

100/120 VAC

@ 34/48 mA

AP9510L630 L6-30 240 24

100/120 VAC

@ 34/48 mA

AP95103202

(international)

IEC320

Quad

240 10

200/240 VAC

@8.5/10 mA

Summary of content (8 pages)

PAGE 1
APC MasterSwitch Power Receptacles (AP9510 Series) Introduction APC® MasterSwitch™ Power Receptacles increase the maxi- mum amperage controlled by a MasterSwitch unit. A North American model of MasterSwitch can supply a maximum of 12 amps total over eight outlets. Using eight 5-15 Power Receptacle units, for example, you can control power to a total load of up to 96 amps— 12 amps per receptacle—using a single MasterSwitch.
PAGE 2
MasterSwitch Power Receptacles continued Warnings Exceeding the voltage or amperage limits for the individual Power Receptacles could cause fire damage or shock. Do not exceed the load capacity of the UPS or branch circuit by connecting more than one fully loaded Power Receptacle. To calculate the expected load, consult the nameplate ratings of all connected equipment. You must maintain reliable grounding of all equipment.
PAGE 3
MasterSwitch Power Receptacles continued Mounting power receptacles in a rack, continued 2. Using a Phillips head screwdriver, remove the four outermost 6-32 screws from the front panel of each Power Receptacle to be mounted in the tray, as shown in the figure below. Remove Screws 3. Remove blanking panels from the front of the Power Receptacle Tray, as necessary. 4.
PAGE 4
MasterSwitch Power Receptacles continued Mounting power receptacles in a rack, continued MasterSwitch Power Module Tray Front Mounting Bracket Acorn Nut Blanking Panel Connecting the power receptacles Power Modules Attach the tray assembly to the rack, using hardware provided with the rack. To connect the Power Receptacle(s), refer to the figure on page 5 and perform the following steps in the order given. 1.
PAGE 5
MasterSwitch Power Receptacles continued Connecting the power receptacles, continued 3. Connect the relay control input cord (on the rear panel of the Power Receptacle) to an outlet on the rear of the MasterSwitch. Plane4 Note: To disconnect, perform steps 1–3 in reverse order. Additional specifications The following table provides Power Receptacle specifications not listed in “Electrical information” on page 1.
PAGE 6
MasterSwitch Power Receptacles continued Limited warranty American Power Conversion (APC) warrants the Power Receptacle to be free from defects in material and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. This warranty does not apply to equipment which has been damaged by accident, negligence, or misapplication or has been altered or modified in any way.
PAGE 7
MasterSwitch Power Receptacles continued Examples of lifesupport devices The term life-support device includes, but is not limited to, neonatal oxygen analyzers, nerve stimulators (whether used for anesthesia, pain relief, or other purposes), autotransfusion devices, blood pumps, defibrillators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incubators, ventilators (for adults or infants), anesthesia ventilators, infusion pumps, and any o
PAGE 8
MasterSwitch Power Receptacles continued Additional safety warrnings continued Italiano • Prima di collegare il cavo di controllo a due conduttori, collegare sempre il cavo di alimentazione a tre conduttori. Per interrompere l'alimentazione, staccare il cavo di controllo a due conduttori prima di scollegare il cavo di alimentazione a tre conduttori. • Installare sempre il modulo di alimentazione con il lato destro rivolto verso l'alto.