Specifications

ManualsBrandsAPC Manualselectrical equipment & suppliesBack-UPS 650VA

Back-UPS 650 VA 230 V with AVR

(BX650CI-AS)

Overview

Do not install the unit in direct sunlight, in areas of excessive heat or

humidity, or in contact with fluids

Setup and Installation

Connect the battery

Pull the battery connector handle down, and then push it into the unit.

Connect the equipment to Battery Backup+Surge Protection

Outlets

Connect equipment to the BATTERY BACKUP + SURGE PROTECTION

outlets.

These outlets provide backup power to the connected equipment during power outages. The Back-

UPS must be turned ON in order to supply backup power. These outlets also provide protection to

the connected equipment from power surges or spikes, even if the Back-UPS is turned OFF. Connect

a computer, monitor, modem or other critical devices you want to stay powered during outages or

utility problems into these outlets.

Connect the power cord

Connect the Back-UPS power cord to the outlet on the back of the unit and to a wall outlet. Do not

connect the power cord to a surge protector or power strip. The outlet should be near the equipment

and easily accessible.

Connect the telephone cord

Connect a phone line from the wall jack to the IN outlet on the UPS. Then, connect a phone, fax

machine, or modem to the OUT outlet on the UPS using a phone cable.



ON/OFF button



Battery connector



Circuit breaker



USB port



Tel/Network ports



Input power outlet



Battery and surge protected outlets

bu 20 0a

Summary of content (6 pages)

PAGE 1
Back-UPS 650 VA 230 V with AVR (BX650CI-AS) Overview Do not install the unit in direct sunlight, in areas of excessive heat or humidity, or in contact with fluids ON/OFF button Battery connector Circuit breaker USB port Tel/Network ports Input power outlet Battery and surge protected outlets bu200a Setup and Installation Connect the battery Pull the battery connector handle down, and then push it into the unit.
PAGE 2
Turn on the power to the unit Press the ON/OFF button on the front of the unit. The unit will emit a single, short “beep” and the green POWER ON indicator will illuminate to confirm that the unit is on and is providing power protection. To provide maximum runtime, the Back-UPS should charge for at least 10 hours. The unit is being charged whenever it is connected to utility power, even if the unit is OFF.
PAGE 3
Adjust the settings If the Back-UPS switches to battery power too frequently or too infrequently, adjust the transfer voltage and sensitivity settings: 1. Ensure the battery is connected and that the Back-UPS is OFF, but connected to utility power. 2. Press and hold the ON/OFF button until the LED repeatedly flashes.The unit is now in Program Mode. 3. Release the button. The LED will indicate the current setting by flashing once, twice, or three times per second, and emitting audible beeps. 4.
PAGE 4
Status Indicators LED On Audible Alarm Off Constant Tone Condition On-line - The Back-UPS is supplying utility power to the connected equipment On Line Overload - The power being used by the connected equipment has exceeded the capacity of the unit. Disconnect some equipment Constant beeping Over-temperature Warning - The unit is overheating and will shut down if the temperature is not lowered. Disconnect some of the connected equipment.
PAGE 5
Problem Probable Cause Solution The ON/OFF button is lit, and The unit is using battery. the unit is beeping four times every 30 seconds, or it is emitting a constant tone. The unit is operating normally and using battery power. Save any current work, turn off all equipment, and turn the unit OFF. Once normal power is restored, turn the unit back ON, and turn on all equipment.
PAGE 6
Specifications Input Output Voltage 230 VAC nominal Frequency 45-65 Hz Brownout Transfer 140 VAC, typical Over-voltage Transfer 300 VAC, typical UPS Capacity (total) 650 VA / 390 W Voltage On Battery 230 Vac rms (step-approximated sine wave) Frequency - On Battery 50 Hz ±1 Hz, 60 Hz ±1 Hz Transfer Time 6ms typical Protection AC Surge Protection and AC Input Filtering Full time, 273 joules Battery Type (maintenance-free) 12V, 7.