Specifications

ManualsBrandsAPC Manualselectrical equipment & suppliesBack-UPS 750VA

Installation and Operation

Back-UPS

BE750G Series

Safety

Specifications

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in contact with fluids, or where there

is excessive dust or humidity.

Connect the Back-UPS power cord directly to a wall outlet. Do not use a surge

protector or an extension cord.

Input

Voltage 120 Vac Nominal

Frequency 50 Hz/60 Hz auto sensing

Brownout Transfers 92 Vrms Typical

Over-voltage Transfer 139 Vrms Typical

Output

UPS Capacity

(5 battery backup outlets)

750 VA, 450 W

Total Amperage (all outlets) 12 A (including UPS output)

Voltage - On Battery 115 Vrms ± 8% step approximated sine wave

Frequency - On Battery 50 Hz/60 Hz ± 1 Hz

Transfer Time 6 ms Typical, 10 ms maximum

Protection and

Filtering

AC Surge Protection Full time, 354 Joules

Phone/DSL/FAX surge protection Single line (2 wire)

Cable/CAT V/DSS surge protection One coax input/output

Network surge protection 10/100 Base -T ethernet

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead acid

Replacement battery cartridge RBC17

Average Life 3 - 5 years depending on the number of discharge cycles and

environmental temperature

Physical

Net Weight 11 lb (5 kg)

Dimensions

Length x Width x Height

14 in x 7 in x 4 in

36 cm x 18 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity 0 to 95% non-condensing humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Summary of content (8 pages)

PAGE 1
Installation and Operation Back-UPS® BE750G Series Safety This unit is intended for indoor use only. Do not operate this unit in direct sunlight, in contact with fluids, or where there is excessive dust or humidity. Connect the Back-UPS power cord directly to a wall outlet. Do not use a surge protector or an extension cord.
PAGE 2
Connect the Battery The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop! Connect the Battery” label that covers the outlets. Prior to connecting any equipment to the unit, connect the battery cable to the unused battery terminal. It is normal for small sparks to be seen when the battery cable is connected to the battery terminal.
PAGE 3
Connect Modem/Telephone/DSL/FAX/10/100 Base-T Network Cable Cable In Cable Out Circuit Breaker Push to Reset Network/DSL/Modem/FAX PowerChute USB Port In Out Building Wiring Fault CAUTION-Refer to bottom of unit for safety markings. bu209a The Back-UPS protects a single line, 2 wire telephone line, including a Digital Subscriber Line (DSL), a modem, a 10/100 Base-T ethernet, or a FAX machine from power surges when connected through the Back-UPS coaxial connectors.
PAGE 4
Turn On the Back-UPS Press the Power ON button located on the top of the Back-UPS. The Power On/Replace Battery LED will illuminate green and a single short beep will be audible to indicate that the Back-UPS is providing protection for connected equipment. The Back-UPS battery charges fully during the first 16 hours while connected to utility power. The Back-UPS battery will charge while the Back-UPS is switched on or off and is connected to utility power.
PAGE 5
Status Indicators Status Power On The Back-UPS is supplying utility power to connected equipment. LED Indicator The green LED illuminates. Audible Indicator Terminates Audible Indicator On None N/A On Battery The green LED illuminates.The Back-UPS beeps 4 times every Back-UPS supplying battery LED is not illuminated during 30 seconds. power to battery backup outlets. the beeps. Beeping stops when utility power is restored or the Back-UPS is turned off.
PAGE 6
Voltage Sensitivity Adjustment The Back-UPS detects and reacts to line voltage distortions by transferring to battery backup power to protect connected equipment. In situations where either the Back-UPS or the connected equipment is too sensitive for the input voltage level it is necessary to adjust the transfer voltage setting. 1. Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode, no indicators will be illuminated. 2. Press and hold the ON/OFF button for 10 seconds.
PAGE 7
Troubleshooting Problem and Possible Cause Solution The Back-UPS will not turn on The Back-UPS has not been turned on. Press the POWER ON button. The Back-UPS is not connected to utility power, there is no Make sure the power cord is securely connected to the wall outlet, utility power available at the wall outlet, or the utility power and that there is utility power available at the wall outlet.Where is experiencing a brownout or over voltage condition.
PAGE 8
Replace Battery Use only approved APC replacement battery cartridge. Deliver used batteries to a battery replacement facility in the packaging provided by APC with the replacement battery cartridge. To order replacement battery cartridges contact APC through the Web site www.apc.com. Warranty The standard warranty is 3 years in the USA and Canada, 2 years in all other regions from the date of purchase. APC standard procedure is to replace the original unit with a factory reconditioned unit.