User's Manual

ManualsBrandsAPC ManualsComputersBack-UPS 6-Outlet Surge Protector and Battery Backup

Table Of Contents

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and

dealer if there is any damage.

SAVE THESE INSTRUCTIONS - This section contains important

instructions that should be followed during installation and maintenance

of the UPS and batteries.

Inventory

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive

dust or humidity.

• Connect the UPS power cable directly to a wall outlet.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

Failure to follow these instructions will result in death or serious injury.

User Manual Back-UPS

™

BE425M/425M-LM, BN450M/450M-CA

Summary of content (12 pages)

PAGE 1
User Manual Back-UPS™ BE425M/425M-LM, BN450M/450M-CA Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation and maintenance of the UPS and batteries. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • • • • This UPS is intended for indoor use only.
PAGE 2
Connect the Battery The Back-UPS is shipped with one battery cable disconnected. bu46 2a bu46  Remove the “Stop! Connect the Battery” label that covers the outlets. bu46 3a  The battery connector is located on the underside of the unit. 4a bu 46 5a  Slide the battery connector handle away from its  Turn the battery connector to a 90-degree upright position and push it into the unit. disconnected position.
PAGE 3
Model Physical Net Weight Dimensions LxWxH Operating Temperature Storage Temperature Operating Relative Humidity Operating Elevation BE425M / BE425M-LM BN450M / BN450M-CA 5.7 lb (2.6 kg) 9.98 in x 4.13 in x 5.51 in 25.35 cm x 10.5 cm x 14.
PAGE 4
Turn Off the Back-UPS Press the POWER button for at least 2 seconds. At the first beep, release the button and the UPS will turn off. A 2 second delay has been added to mitigate unintentional contact with the POWER button. Quick Mute The Back-UPS is able to temporarily mute user correctable alarms such as On Battery. During such alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the alarm until the condition has been reset.
PAGE 5
LED Flashes Input Voltage Range (AC Operation) Sensitivity Setting Recommended Use Green LOW 88 Vac to 142 Vac Use this setting with equipment that is less sensitive to fluctuations in voltage or waveform distortions. Red MEDIUM 92 Vac to 139 Vac Factory default setting. Use this setting under normal conditions. Amber HIGH Use this setting when connected equipment is sensitive to voltage and waveform fluctuations.
PAGE 6
Troubleshooting Problem and Possible Cause Solution The Back-UPS will not turn on The Back-UPS is not connected to AC power, Make sure the power cord is securely connected to there is no AC power available at the wall outlet, the wall outlet, and that there is AC power available or the AC power is experiencing a brownout or from the wall outlet.Where applicable, check that over voltage condition. the wall outlet is switched on.
PAGE 7
Wall Mount Installation • Horizontal installation, use 2 screws 7.63” (194 mm) apart. • Allow 5/16” (8 mm), of the screw to protrude from the wall. 7.63 in. 194 mm Wall-mounting Template bu380d Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the manual to eliminate common problems. 2. If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the APC by Schneider Electric Web site, www.apc.com.
PAGE 8
Battery Replacement CAUTION HAZARD OF EXPLOSION • Do not dispose of the batteries in a fire. The batteries may explode. • Do not open or mutilate the batteries. Release electrolyte may be toxic and it is harmful to the skin and eyes. Failure to follow these instructions can result in injury. The battery in the Back-UPS is not user-replaceable. Contact SEIT Technical Support for a list of authorized service centers near you. Warranty Register your product on-line. http://warranty.apc.
PAGE 9
Safety Information - SAVE THIS GUIDE This Safety Guide contains important instructions that should be followed during installation and maintenance of the APC by Schneider Electric equipment and batteries. It is intended for APC by Schneider Electric customers who setup, install, relocate, or maintain APC by Schneider Electric equipment. Read, understand, and follow ALL safety instructions contained in this manual.
PAGE 10
• The ground conductor must be grounded to earth at the service equipment, or if supplied by a separately derived system, at the supply transformer or motor generator set. • Connect the equipment to a three wire utility outlet (two poles plus ground). The receptacle must be connected to appropriate branch circuit/mains protection (fuse or circuit breaker). Connection to any other type of receptacle may result in risk of electrical shock. • Leakage current for a pluggable Type A UPS may exceed 3.
PAGE 11
THIS POLICY IS NOT A WARRANTY. REFER TO THE LIMITED WARRANTY FOR INFORMATION CONCERNING THE WARRANTY FOR YOUR APC PRODUCT. THE LIMITATIONS AND CONDITIONS IN THIS POLICY DO NOT AFFECT THE TERMS OF THE WARRANTY.
PAGE 12
OF THE APC PRODUCT OR THE CONNECTED EQUIPMENT OR ANY ASSOCIATED EQUIPMENT, LOSS OF SOFTWARE, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT, FACILITIES OR SERVICES, LABOR, DOWNTIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. Submitting an Equipment Protection Policy Claim: 1.