User Manual

ManualsBrandsAPC ManualsPOWERUPS, 400W, 230V, 3Ax Type L

Important Safety Information

SAVE THESE INSTRUCTIONS - This manual contains important

instructions that should be followed during installation and maintenance of the

Back-UPS and batteries.

Read these instructions carefully and look at the equipment to become familiar

with the device before trying to install, operate, service or maintain it. The

following special messages may appear throughout this document or on the

equipment to warn of potential hazards or to call attention to information that

clarifies or simplifies a procedure.

The addition of this symbol to either a “Danger” or “Warning”

safety label indicates that an electrical hazard exists which will

result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical

injury.

User Manual Back-UPS™

BE650G2-IT and BE850G2-IT

Summary of content (16 pages)

PAGE 1
User Manual Back-UPS™ BE650G2-IT and BE850G2-IT Important Safety Information SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation and maintenance of the Back-UPS and batteries. Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it.
PAGE 2
Product Handling Guidelines <18 kg <40 lb 18-32 kg 40-70 lb 32-55 kg 70-120 lb >55 kg >120 lb Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. • This UPS is for indoor use only. • Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or high humidity. • Do not operate the UPS near open windows or doors. • Be sure the air vents on the UPS are not blocked.
PAGE 3
• CAUTION: Do not dispose of batteries in a fire. The batteries may explode. • CAUTION: Do not open or mutilate batteries. Released material is harmful to the skin and eyes and may be toxic. • CAUTION: A battery can present a risk of electrical shock and high short-circuit current. Failed batteries can reach temperatures that exceed the burn thresholds for touchable surfaces.
PAGE 4
 Connect the battery cable securely to the battery terminal. Note: It is normal for small sparks to be seen when the battery cable is connected to the battery terminal. 3a bu 49  Reinstall the battery compartment cover. Be sure that the release tabs lock into place. b u49 4a Wall Mount Installation CAUTION RISK OF FALLING EQUIPMENT Always practice safe lifting techniques adequate for the weight of the equipment.
PAGE 5
Panel Features Side Panel bu496a Top Panel bu499a  POWER ON/OFF Use to switch the Back-UPS on or off. button and LED       The LED illuminates green to indicate that power is supplied to the connected equipment both on utility power and on battery. See “Status Indicators” on page 9 for other status of the Power on/off LED.
PAGE 6
 DSL/modem network/fax port  Wall outlet  Data port  Circuit Connect a DSL or Dial-up modem, Phone, Fax machine, or 10/100 Base-T Ethernet equipment. Note: Do not connect the UPS telephone protection ports to both the telephone and network system cables at the same time. Connect the Back-UPS to a data line wall outlet. Connect a RJ45/USB cable (not supplied) to connect the Back-UPS to a computer for installing the software. See “UPS Self Test” on page 8 for details.
PAGE 7
Specifications BE650G2-IT BE850G2-IT 220 - 240 Vac 47 to 63 Hz 180 Vac Typical 266 Vac Typical Output 650 VA, 400 W 850 VA, 520 W 2.96 A 3.87 A 6A 230 Vac ± 8% 50/60 Hz ± 1 Hz 6 milliseconds Typical, 10 milliseconds maximum USB Port * Charging Rating 5 V; 2.40 A Charger compatibility USB Battery Charging Specification 1.2 * Power output is dependent on the power drawn by the connected device. Check with the device manufacturer to understand the maximum charging current for a given USB specification.
PAGE 8
Turn On the Back-UPS Press the POWER ON/OFF button located on the top of the Back-UPS. The Power on/off LED will illuminate green and a single short beep will indicate that the Back-UPS is on and providing protection to the connected equipment. The Back-UPS battery charges to capacity during the first 24 hours while connected to the utility power. The Back-UPS battery will charge while the Back-UPS is turned on or off and as long as it is connected to utility power.
PAGE 9
Installation Note: To reduce electronic waste and help protect the environment, USB cables are no longer shipped in every box. Order the cable free of charge at https://www.apc.com/usbcable. Use the USB cable to connect the Data port on the UPS to the USB port on your computer. Download PowerChute™ Personal Edition Software from www.apc.com/pcpe. Select the appropriate operating system and follow directions to download the software.
PAGE 10
Audible Audible indicator Visual indicator indicator Condition terminates Back-UPS is turned Power on/off LED does Constant Overload shutdown - An off. not illuminate tone overload condition in one or more of the battery back up outlets when the Back-UPS is operating on battery power. None USB error detected - A short Not applicable. Power on/off LED circuit or an internal error has flashes green and amber been detected. alternately Mute status LED None Mute function enabled. Not applicable.
PAGE 11
Audible Audible indicator Visual indicator indicator Condition terminates None Battery charge is 75% to 100%. Not applicable. First three Battery status LEDs illuminate and fourth Battery status LED flashes All four Battery status None Battery fully charged and Not applicable. LEDs illuminate Back-UPS is on utility power.
PAGE 12
Replace Battery CAUTION RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE • Replace the battery at least every 5 years or at the end of its service life, whichever is earlier. • Replace the battery immediately when the UPS indicates battery replacement is necessary. • Replace batteries with the same number and type of batteries as originally installed in the equipment.
PAGE 13
Problem Possible Cause The Back-UPS Back-UPS circuit breaker will not turn on. tripped. The Back-UPS The battery is disconnected. is on, the Power on/off LED flashes red and the unit emits a constant tone. Connected A Back-UPS overload equipment loses condition has occurred. power. The Back-UPS battery is completely discharged. PowerChute software has performed a shutdown due to a power outage. Connected equipment does not accept the step-approximated sine waveform from the Back-UPS.
PAGE 14
Problem Possible Cause The Back-UPS is operating on The Power On/Off LED is battery power. green and flashes twice every 2 seconds. The Power On/Off LED flashes green in rapid succession. The Back-UPS battery has approximately two minutes of remaining runtime. The Back-UPS The battery is not fully has an charged. inadequate battery runtime. The battery is near the end of useful life and should be replaced. USB charging is Charging a device using the slow.
PAGE 15
Warranty Register your product on-line. http://warranty.apc.com The standard warranty is three (3) years from the date of purchase valid in European Community. For all other regions, the standard warranty is two (2) years from the date of purchase. Schneider Electric IT (SEIT) standard procedure is to replace the original unit with a factory reconditioned unit.
PAGE 16
APC by Schneider Electric IT Customer Support Worldwide For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com. © 2022 APC by Schneider Electric. APC, the APC logo, Back-UPS, and PowerChute are owned by Schneider Electric Industries S.A.S., or their affiliated companies. All other trademarks are property of their respective owners.