User Manual

ManualsBrandsAPC ManualsComputer Accessories & PeripheralsAPC Sine Wave UPS Battery Backup & Surge Protector, 1350VA, APC Back-UPS Pro (BR1350MS)

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and

dealer if there is any damage.

SAVE THESE INSTRUCTIONS - This section contains important

instructions that should be followed during installation and maintenance

of the UPS and batteries.

Inventory

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive

dust or humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

Failure to follow these instructions will result in death or serious injury.

CAUTION

RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE

• Connect the UPS power cable directly to a wall outlet.

• Battery must be replaced when they reach end of service life.

• Batteries must be replaced when the unit indicates battery replacement is necessary.

• When replacing batteries, replace with the same number and type of batteries originally

installed in the unit.

Failure to follow these instructions could result in minor or moderate injury and

equipment damage.

bu476a

Coaxial cable

USB communication cable

User Manual Back-UPS

™

Pro

BR 1000/1350/1500 MS

Summary of content (12 pages)

PAGE 1
User Manual Back-UPS™ Pro BR 1000/1350/1500 MS Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation and maintenance of the UPS and batteries. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • • • This UPS is intended for indoor use only.
PAGE 2
Connect the Battery bu471a The UPS is shipped with the battery disconnected. bu47 2a bu474a bu473a  Lay the UPS with the battery door facing  Press the tabs downwards and pull the up. The arrows point to the locking tabs of the battery door away from the unit to access battery compartment. the battery modules.  Push the battery into the unit.  Using the handles on both sides of the battery, lift the battery 30 degrees upward to expose the battery connector. Connect the red wire as shown above.
PAGE 3
Connect the Equipment Battery Backup and Surge Protected outlets When the Back-UPS is receiving input power, the Battery Backup with Surge Protection outlets will supply power to connected equipment. During a power outage or other AC problems, the Battery Backup outlets receive power for a limited time from the BackUPS. Connect equipment such as printers, fax machines, scanners, or other peripherals that do not need battery backup power to the Surge Protection Only outlets.
PAGE 4
Operation Power Saving Display The display interface can be configured to be continuously illuminated, or to save energy, it can be configured to darken after a period of inactivity. 1. Full Time Mode: Press and hold DISPLAY for two seconds. The display will illuminate and the Back-UPS will beep to confirm the Full Time mode. 2. Power Saving Mode: Press and hold DISPLAY for two seconds. The display will darken and the Back-UPS will beep to confirm the Power Saving mode.
PAGE 5
Front Panel Buttons and Display Interface Use the three buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS. Front panel  Display button  Power On/Off button  Mute button  Display interface  USB charging ports: bu470b The 2 USB ports provide a total of 15W of DC power, and will provide power even when the UPS is on battery.
PAGE 6
Mute: If the line through the speaker icon is illuminated, the audible alarm has been turned off. Out: Output voltage, frequency In: Input voltage. Automatic Voltage Regulation: When illuminated, the Back-UPS is compensating for low input voltage When illuminated, the Back-UPS is compensating for high input voltage. Estimated Run Time: This indicates the battery runtime minutes that remain if the Back-UPS switches to battery power.
PAGE 7
System Errors The Back-UPS will display these error messages. Except for errors F01 and F02, contact SEIT Technical Support. F01 bu088d F02 F04 F05 F06 F07 F08 F09 Turn the Back-UPS off. Disconnect non-essential On-Battery Overload equipment from the Battery Backup outlets and the turn Back-UPS on. Turn the Back-UPS off. Disconnect all equipment from the Battery Backup outlets and On-Battery Output the turn Back-UPS on. Re-connect equipment one item Short at a time.
PAGE 8
Function Button Quick Reference Timing (seconds) UPS Status Power On 0.2 Off Power Off 2 On 0.2 On Verify the status or condition of the Back-UPS. The LCD will illuminate for 60 seconds. Press the button the toggle into various information. 2 On The LCD will illuminate and the Back-UPS will beep to confirm the Full-Time mode. The LCD will darken and the Back-UPS will beep to confirm the PowerSaving mode.
PAGE 9
Troubleshooting Problem Possible Cause Corrective Action The Back-UPS is not connected to AC Ensure that the Back-UPS is securely power. connected to an AC outlet. The circuit breaker has been tripped. Back-UPS will not switch on. Disconnect non-essential equipment from the Back-UPS. Reset the circuit breaker. Re-connect equipment one item at a time. If the circuit breaker is tripped again, disconnect the device that caused the trip. The internal battery is not connected. Connect the battery.
PAGE 10
Specifications VA Maximum Load BR1000MS BR1350MS BR1500MS 1000 VA 1350 VA 1500 VA 600W 810W 900W Nominal Input Voltage 120 V Online Input Voltage Range Automatic Voltage Regulation 88 - 147 V Boost by +11.5% when input voltage drops below limit Trim by -11.
PAGE 11
APC by Schneider Electric IT Customer Support Worldwide For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com. Select models are ENERGY STAR® qualified. For more information on your specific model go to www.apc.com. This UPS is certified to comply with California Battery Charger System regulations. For more information go to www.apc.
PAGE 12
© 2017 APC by Schneider Electric. APC, the APC logo, and Back-UPS are owned by Schneider Electric Industries S.A.S. or their affiliated companies. All other trademarks are property of their respective owners.