Manual

ManualsBrandsAPC ManualsComputersPower-Saving Back-UPS Pro 1500 International Version

Back-UPS

Pro 1200/1500 230V

Installation and Operation

Connect the battery

Install PowerChute

Personal Edition Software

APC PowerChute Personal Edition software provides automatic file saving and shutdown of

your computer in the event of a power failure. Use the cable supplied with the Back-UPS to

connect the data port on the Back-UPS to the USB port on your computer. Place the CD into

your computer, and follow the on-screen instructions.

Inventory Safety

Do not install the Back-UPS in direct

sunlight, in excessive heat, humidity, or

in contact with fluids.





bu001a

(2)

bu055a

bu057a

bu059a

bu058a

bu060a

Summary of content (8 pages)

PAGE 1
Back-UPS® Pro 1200/1500 230V Installation and Operation Inventory Safety (2) bu001a Do not install the Back-UPS in direct sunlight, in excessive heat, humidity, or in contact with fluids. Connect the battery   bu055a bu057a bu059a  bu060a  bu058a  Install PowerChute® Personal Edition Software APC PowerChute Personal Edition software provides automatic file saving and shutdown of your computer in the event of a power failure.
PAGE 2
Connect the equipment Battery Backup and Surge Protected outlets When the Back-UPS is receiving input power, the Battery Backup with Surge Protection outlets will supply power to connected equipment. During a power outage or other utility problems, the Battery Backup outlets receive power for a limited time from the Back-UPS.
PAGE 3
Operation Power-Saving Function To conserve electricity, configure the Back-UPS to recognize a Master device, such as a desktop computer or an A/V receiver, and Controlled peripheral devices, such as a printer, speakers, or a scanner. When the Master device goes into Sleep or Standby mode, or is switched OFF, the Controlled device(s) will be switched off as well, saving electricity. Enable the Power-Saving function. Press and hold MUTE and DISPLAY simultaneously for two seconds.
PAGE 4
Front Panel Buttons and Display Interface Use the three buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS.
PAGE 5
Warnings and System Faults Audible Warnings Back-UPS is running on battery. You should consider saving any work in progress. Low battery condition and battery run-time is very low. Promptly save any work in progress, exit all open applications, and shut down the operating system. Battery Backup outputs are overloaded. Four Beeps Every 30 Seconds Continuous Beeping Continuous tone Chirps for 1 Minute every 5 hours Battery fails the automatic diagnostic test and should be replaced.
PAGE 6
Function Button Quick-Reference Function Timing Button (seconds) UPS Status Description Power Power On 0.2 Off Press POWER to start receiving input utility power. If A/C input power is not available, the Back-UPS will run on battery power. Power Off 2 On The Back-UPS is not receiving input utility power, but is providing surge protection. 0.2 On Verify the status or condition of the Back-UPS. The LCD will illuminate for 60 seconds.
PAGE 7
Troubleshooting Problem Possible Cause Back-UPS will not switch on. The Back-UPS is not connected to utility power. The circuit breaker has been tripped. The internal battery is not connected. The utility input voltage is out of range. The Back-UPS does not Ensure that essential equipment is not provide power during a utility plugged into a SURGE ONLY outlet. power outage.
PAGE 8
Specifications Replacement Battery t Model BR1200GI BR1500GI VA 1200 VA 1500 VA Maximum Load 720 W 865 W Nominal Input Voltage 230 V Online Input Voltage Range 176 - 294 V Automatic Voltage Regulation (188-216) +11.2% (252-282) -11.2% The battery cartridge typically lasts 3 to 6 years, a shorter period if subjected to frequent outages or elevated temperatures. Battery replacement part for Back-UPS Pro 1200 and 1500 is APCRBC124. Please recycle spent battery cartridges.