User Manual

ManualsBrandsAPC ManualsPOWERUPS, 300W, 230V, x IEC 60320 C13, 4.5Ah

Safety and General Information

SAVE THESE INSTRUCTIONS –

This manual contains important instructions that should be followed during installation and

maintenance of the UPS and batteries.

Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damages.

 This UPS is intended for indoor use only.

 Mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily

accessible.

 UPS must be connected to an earthed mains socket outlet.

HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE

 Battery must be replaced when they reach end of service life.

 Batteries must be replaced when the unit indicates battery replacement is necessary.

 When replacing batteries, replace with the same number and type of batteries originally installed in the unit.

Failure to follow these instructions can result in minor or moderate injury and

equipment damage.

 Servicing of batteries should be performed or supervised by personnel knowledgeable about

batteries and required precautions.

 When replacing battery the UPS must be OFF, and its AC inlet unplugged.

 CAUTION Do not dispose of batteries in a re. The batteries may explode.

 CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions.

 Do not open or mutilate batteries. They contain an electrolyte that is toxic and harmful to the skin

and eyes.

 CAUTION A battery can present a risk of electrical shock and high short circuit current.

The following precautions should be observed when working on batteries.

a. Remove watches, rings or other metal objects.

b. Use tools with insulated handles.

c. Wear rubber gloves and boots.

d. Do not lay tools or metal parts on top of batteries.

e. Disconnect the charging source prior to connecting or disconnecting battery terminals.

f. Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from

ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood

of such shock can be reduced if such grounds are removed during installation and maintenance

Radio Frequency Warning

This is a category C2 UPS product. In a residential environment, this product may cause radio

interference, in which case the user may be required to take additional measures.

User Manual Easy UPS

BV Series 500VA, 650VA, 800VA, 1000VA

CAUTION

Summary of content (6 pages)

PAGE 1
User Manual Easy UPS BV Series 500VA, 650VA, 800VA, 1000VA Safety and General Information SAVE THESE INSTRUCTIONS – This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damages.  This UPS is intended for indoor use only.  Mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible.
PAGE 2
Place and Power On 1. Place the Easy UPS to avoid:  Direct sunlight  Excessive heat  Excessive moisture  Excessive dust/dirt For operation, please place the unit on the floor. 2. Connect the battery by pulling the battery handle up, and then pushing it into the unit. 3. Connect equipment to the UPS. Avoid using extension cords. 4. Plug the Easy UPS power cord directly into a wall outlet, not into a surge protector or power strip. 5. Press the ON/OFF button to turn on the unit.
PAGE 3
Specifications Model Input BV500I BV650I Brownout Transfer 170 VAC, typical 280 VAC, typical Over-voltage Transfer 500VA / 300W 650VA / 375W 800VA / 450W 1000VA / 600W UPS Capacity (total) 230VAC ± 10% Voltage On Battery Frequency - On Battery 50 Hz / 60 Hz ± 1Hz Transfer Time 6ms typical Protection AC Input Circuit Breaker* (*only for model with Schuko outlet) AC Input Fuse Battery BV1000I 50 Hz or 60 Hz Frequency Output BV800I 230 VAC Voltage Type (maintenance-free) Average Life 5A
PAGE 4
Status Indicators LED Audible Alarm On Off On Condition On-line - The Easy UPS is supplying AC power to the connected equipment Constant Tone On Line Overload - The power being used by the connected equipment has exceeded the capacity of the unit. Disconnect some equipment. Constant beeping (every 1/2 second) Over-temperature - The unit is overheating and will operate in AVR mode for 5 minutes. The Easy UPS will shut down if the temperature is not lowered.
PAGE 5
Troubleshooting Problem and Possible Cause The Easy UPS will not turn on Solution The Easy UPS has not been turned on. The Easy UPS is not connected to AC power, there is no AC power available at the wall outlet, or the AC power is experiencing a brownout or over voltage condition. Press the ON/OFF button. Make sure the power cord is securely connected to the wall outlet, and that there is AC power available at the wall outlet.Where applicable, check that the wall outlet is switched on.
PAGE 6
Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the manual to eliminate common problems. 2. If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the APC by Schneider Electric website, www.apc.com. a. Note the model number and serial number and the date of purchase. The model and serial numbers are located on the rear panel of the unit. b.