User Manual

ManualsBrandsAPC ManualsComputer Accessories & PeripheralsAPC UPS Battery Backup & Surge Protector with AVR, 1000VA, APC Back-UPS Pro (BX1000M)

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and

dealer if there is any damage.

SAVE THESE INSTRUCTIONS - This section contains important

instructions that should be followed during installation and maintenance

of the UPS and batteries.

Inventory

Connect the Battery

The UPS is shipped with the battery disconnected.

BX850/1000M/M-LM60

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive

dust or humidity.

• Connect the UPS power cable directly to a wall outlet.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

Failure to follow these instructions will result in death or serious injury.

 Remove the battery door.

 Remove the battery. Connect the wire.

bu001b

bu025c

User Manual Back-UPS

™

Pro

BX850/1000/1350/1500M/M-LM60

Summary of content (10 pages)

PAGE 1
User Manual Back-UPS™ Pro BX850/1000/1350/1500M/M-LM60 Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. SAVE THESE INSTRUCTIONS - This section contains important instructions that should be followed during installation and maintenance of the UPS and batteries. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • • • • This UPS is intended for indoor use only.
PAGE 2
bu026c  Replace the battery door.  Push the battery into the unit. bu055b bu057b BX1350/1500M/M-LM60  Remove the battery.  Push the battery into the unit. bu060b  Flip or turn the battery 180 degrees upward/downward to let green side of the label face up. bu058b bu059b  Remove the battery door.  Replace the battery door. Install PowerChute™ Personal Edition Software Use PowerChute Personal Edition software to configure the UPS settings.
PAGE 3
Connect the Equipment Battery Backup and Surge Protected outlets When the Back-UPS is receiving input power, the Battery Backup with Surge Protection outlets will supply power to connected equipment. During a power outage or other AC problems, the Battery Backup outlets receive power for a limited time from the BackUPS. Connect equipment such as printers, fax machines, scanners, or other peripherals that do not need battery backup power to the Surge Protection Only outlets.
PAGE 4
 In/Out Ethernet Use an Ethernet cable to connect a cable modem to the IN port, surge-protected and connect a computer to the OUT port. ports  Coaxial ports Connect a cable modem or other equipment with coaxial jacks. with surge protection Operation Power Saving Display The display interface can be configured to be continuously illuminated, or to save energy, it can be configured to darken after a period of inactivity. 1. Full Time Mode: Press and hold DISPLAY for two seconds.
PAGE 5
Front Panel Buttons and Display Interface Use the three buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS. Front panel  Mute button  Power On/Off button bu109g  Display button  Display interface On Line: The Back-UPS is supplying conditioned AC power to connected equipment Load Capacity: The load is indicated by the number of sections illuminated, one to five. Each bar represents 20% of the load.
PAGE 6
Replace Battery: The battery is nearing the end of its useful life. Replace the battery as early as possible. On Battery: The Back-UPS is supplying battery backup power to the connected equipment, it will beep four times every 30 seconds. Alarms and System Errors Audible Indicators Back-UPS is running on battery. You should consider saving any work in progress. Low battery condition and battery run-time is very low.
PAGE 7
System Errors The Back-UPS will display these error messages. Except for errors F01 and F02, contact SEIT Technical Support. F01 F02 bu088a F03 F04 F05 F06 F07 F09 Turn the Back-UPS off. Disconnect non-essential On-Battery Overload equipment from the Battery Backup outlets and the turn Back-UPS on. Turn the Back-UPS off. Disconnect all equipment from the Battery Backup outlets and On-Battery Output the turn Back-UPS on. Short Re-connect equipment one item at a time.
PAGE 8
Function Button Timing (seconds) UPS Status Description Sensitivity 6 Off The Load Capacity icon will blink, indicating that the Back-UPS is in programming mode. Use the POWER button to scroll through Low, Medium, and High, stop at selected sensitivity. The Back-UPS will beep to confirm selection. See "Unit sensitivity" for details. Self-Test (manual) 6 On The Back-UPS will perform a test of the internal battery.
PAGE 9
Problem Possible Cause Corrective Action The REPLACE The battery has reached the end of its Replace the battery as early as possible. BATTERY indicator is useful life. illuminated. The OVERLOAD indicator is illuminated. The SYSTEM ERROR indicator is illuminated, all the front panel indicators are flashing. The equipment connected to the Back-UPS is drawing more power than the Back-UPS can provide.
PAGE 10
Warranty The standard warranty is three (3) years from the date of purchase. Schneider Electric IT (SEIT) standard procedure is to replace the original unit with a factory reconditioned unit. Customers who must have the original unit back due to the assignment of asset tags and set depreciation schedules must declare such a need at first contact with an SEIT Technical Support representative.