™ Line-R Models 600 and 1250 User’s Manual
Thank you! Thank you for selecting this American Power Conversion Line-R™ brand power conditioner. This power conditioner provides the highest degree of protection from line voltage sags, swells, spikes, surges, and electrical noise. It has been designed for many years of reliable, maintenance-free service.
1.0 Introduction 1.1 Overview This power conditioner is a high-performance, microprocessor-controlled tap changing power conditioner which automatically corrects brownouts and overvoltages from your power utility service to levels that are safe for your computer and phone systems, and other sensitive equipment. 1.2 Voltage regulation Chronically abnormal line voltage is often the result of adjustments made at the power station to conserve energy or to compensate for low voltages in other areas.
2.0 Safety ! Before starting your installation, please read the following safety instructions! ■ The power conditioner is intended for indoor use only. ■ Operate the power conditioner in an area with adequate air flow, and an atmosphere free of excessive dust and corrosive fumes. Do not block the ventilation openings. ■ Do not place the power conditioner near heat-emitting appliances such as radiators or stoves. ■ Avoid installing the power conditioner where there is water or excessive humidity.
3.0 Presentation 3.1 600 and 1250 VA power conditioners—front panel Very High High Normal Input voltage level indicators Low Very Low all versions Surge Protection Integrity indicator 3.
4.0 Installation 4.1 Receiving inspection Remove the power conditioner from its shipping container and inspect it for damage that may have occurred in transit. Notify the carrier and place of purchase if any damage is found. The packing materials are made of recyclable materials and should be saved for reuse or disposed of properly. 4.2 Placement You may install the power conditioner in any protected environment.
4.0 Installation 4.3 Connect the power conditioner to service and enable ■ 120 Vac version Plug the power conditioner into a two-pole, three-wire grounding receptacle only. Avoid using extension cords and adapter plugs. ■ 230 Vac version The 230 Vac version of the power conditioner is supplied with two output IEC 320 cords. Swap a line cord from your equipment with one of the output cords and plug in the power conditioner using the equipment cord.
4.0 Installation 4.4 Connect the load equipment Plug your equipment into the power conditioner’s rear-panel receptacles. You may switch the equipment on, but they will not be powered until you switch on the power conditioner. Make sure the your total equipment load does not exceed the power conditioner’s rated capacity (listed on the rear-panel). 4.5 Switch on the power conditioner Switch on the power conditioner by pressing the rear-panel Power switch to the on ( I ) position.
5.0 Operation 5.1 Front-panel indicators 5.1.1 Very High input voltage indicator The Very High indicator lights when the power conditioner is regulating input voltage which is approaching the upper limit of the conditioner’s rated range. 5.1.2 High input voltage indicator The High indicator lights when the power conditioner is regulating input voltage which is above normal. 5.1.3 Normal input voltage indicator The Normal indicator lights when the input voltage is normal. 5.1.
6.0 Specifications 6.1 Input version: 120 Vac 230 Vac 50 or 60 Hz Frequency: Model 600 maximum current: 8 Amp 3.5 Amp Model 1250 maximum current: 15 Amp 7 Amp 6.2 Output Model 600 maximum capacity: 600 W or 600 VA Model 1250 maximum capacity: 1250 W or 1250 VA 6.3 Regulation Input (Vac) Output (Vac) Regulation 88 to 150 106 to 127 ANSI C84.1-B 92 to 145 111 to 123 117 Vac ±5% 182 to 287 219 to 242 230 Vac ±5% 6.
Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from APC or an APC service center.
( PHONE ( PHONE (800) 800-4272 in USA & Canada (401) 789-5735 worldwide (+33) 1.64.62.59.00 in Europe (401) 789-5735 worldwide * MAILING * MAILING American Power Conversion 132 Fairgrounds Road P.O.
