Installation Guide NetBotz® Wireless Sensor Pod 180 NBPD0180
Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Supported appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Supported sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ZigBee® Certified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Document overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring and Monitoring Sensors . . . . . . . . . . . . . . . . . . . . . 15 Receiving and sending data . . . . . . . . . . . . . . . . . . . . . . 15 Updating the Wireless Sensor Pod. . . . . . . . . . . . . . . . . . . . . . . 16 Cleaning the Wireless Sensor Pod . . . . . . . . . . . . . . . . . . . . . . . 16 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Two Year Limited Factory Warranty . . . . . . . . . . . . . . . . . . . . . .
Introduction Product description The NetBotz® Wireless Sensor Pod 180 (NBPD0180) connects to a NetBotz appliance and allows you to monitor the temperature and humidity in a rack in your data center. Additional sensors allow you to monitor rack door access, and multiple temperature readings for the rack. The Wireless Sensor Pod 180 can be configured as the Coordinator, a Router, or an End Device in your wireless sensor network.
ZigBee® Certified The Wireless Sensor Pod is ZigBee Certified. ZigBee is a wireless mesh networking standard for low-power applications. Schneider Electric is a member of the ZigBee Alliance. Full information on the ZigBee standard can be found at the ZigBee Alliance website: http://www.zigbee.org.
Physical Description Front view Item Description Battery Holds 2 AA batteries when in End Device mode. Compartment Universal Sensor Port for a Temperature Probe or Door Contact sensor. Port #2 Universal Sensor Port #3 Port for a Temperature Probe or Door Contact sensor. Type-B USB Port Used to connect the Wireless Sensor Pod to a NetBotz appliance when used in Coordinator mode, or to supply USB power when in Router mode.
Inventory Inspect the contents of the package to ensure that the parts included match those shown below. Report missing or damaged contents to Schneider Electric or your APC reseller. The shipping and packaging materials are recyclable. Please save them for later use or dispose of them appropriately.
Components of the Wireless Sensor Network The Wireless Sensor Pod can be configured to act in three different modes on a ZigBee wireless sensor network: Coordinator, Router, and End Device. The mode of a Wireless Sensor Pod is determined by the manner in which power is supplied to the device. The factory default for the Wireless Sensor Pod is Router mode. Host Appliance. A wireless sensor network is monitored by a single NetBotz appliance, listed in “Supported appliances” on page 1.
Installing the Wireless Sensor Network The order in which you install your wireless network is important. Warning: Although every Wireless Sensor Pod has a battery compartment, ONLY End Devices require batteries. DO NOT insert batteries into a sensor pod that will be a Router or a Coordinator. For best results, power and configure your wireless network as follows: Scan the extended addresses of the Wireless Sensor Pods.
Mounting the Wireless Sensor Pod When planning your wireless network installation locations, place each End Device or Router within range of another Router or a Coordinator. The maximum range of the Wireless Sensor Pod is 100 ft (line of sight). This range is a best-case scenario; the signal will be strongly affected by environmental interference. Use the RSSI sensor reading (available in the device’s sensor listing in Advanced View) to tune device placement. A reading above 30% RSSI is ideal.
External installation The Wireless Sensor Pod ships with a mounting plate to be used when installing a pod in a non-rack location or in a non-Netshelter VX, SX, or SV rack. 1. Separate the two pieces of the plastic push rivets. Note: To avoid equipment damage, use only the hardware provided when installing the brackets. 2. Place the included mounting plate on the back of the pod and align the holes with the mounting holes on the pod. 3.
Powering the Coordinator Power the Coordinator first. Connect one and only one Coordinator to a USB Type A port on the NetBotz appliance. Make a note of the port to which the Coordinator is attached, for example USB-A. Configuring the Coordinator The Coordinator must be configured as a serial device in the Wireless Sensor Setup task in the Advanced View on the host appliance. After connecting the Coordinator: 1. Log in to the host appliance using the Advanced View. 2.
Disconnecting a Coordinator When you disconnect the Coordinator from the host appliance, all of the sensors on the wireless sensor network display as offline. When you reconnect the same Coordinator, it must be manually deleted and reconfigured in the Wireless Sensor Setup task in the Advanced View. The network will then restart, and the sensors will begin reporting data.
Powering a Router A Wireless Sensor Pod must be connected to an AC-USB power source to become a Router. Once its extended address is added to the commission list in the Advanced View, and power is applied, the pod is automatically configured as a Router. Warning: Do not use a NetBotz appliance as the USB power source for a Router device. To configure a Wireless Sensor Pod as a Router: 1. Mount the pod using the instructions in “Mounting the Wireless Sensor Pod” on page 7. 2.
Powering an End Device A Wireless Sensor Pod must have lithium batteries installed to become an End Device. An End Device reports data from the internal and external sensors to the host appliance, but does not extend the wireless network or pass data to other End Devices. Power End Devices last to preserve battery life. Once its extended address is added to the commission list in the Advanced View, and the lithium batteries are installed, the pod is automatically configured as an End Device.
LED Activity The LED on the Wireless Sensor Pod flashes to indicate certain statuses or alerts. During the boot process in all three modes, the LED on the sensor pod flashes yellow rapidly for about 40 seconds, turns solid yellow for 10 seconds, and then flashes a quick green, yellow, red LED sequence.
End Device LED activity LED Behavior Meaning Flashes yellow twice every 3 seconds Flashing yellow, then solid yellow Solid green for 5 seconds, then off Searching for network Booting Joined the network Off Joined the network, or has not joined the network and is conserving battery power. To conserve battery power, the End Device will attempt to join the network after waiting the following number of seconds: 5, 15, 30, 60, 120, 300, 300, 600, 1200.
Note: The Reset button is disabled while the sensor pod is booting. Once startup is complete, the button functions normally. Configuring and Monitoring Sensors Once your wireless network is installed and communicating, configure sensors and begin monitoring your system using the software interface for the appliance. See your appliance installation and quick configuration manual for system installation details and for instructions on accessing the software interface of the appliance.
Updating the Wireless Sensor Pod Firmware updates for the Wireless Sensor Pod are included in the Botzware firmware releases. When a Botzware firmware update is available, you download it from www.apc.com and install it on the NetBotz appliance. The Wireless Sensor Pod configured as the Coordinator receives the firmware update package from the NetBotz appliance over the USB connection.
Specifications Electrical Input voltage, nominal 5v USB; 3.6v battery Maximum total current draw 65mA USB Physical Dimensions (H x W x D) 106.0 x 56.4 x 28.0 mm (4.2 x 2.2 x 1.1 in) Shipping dimensions (H x W x D) 228.6 x 165.1 x 58.0 mm (9.0 x 6.5 x 2.0 in) Weight with batteries with mounting bracket with batteries and bracket 0.1 kg (0.2 lb) 0.15 kg (0.3 lb) 0.15 kg (0.3 lb) 0.2 kg (0.4 lb) Shipping weight 0.45 kg (1.
Two Year Limited Factory Warranty Schneider Electric IT Corporation (SEIT), warrants its products to be free from defects in materials and workmanship for a period of two (2) years excluding the batteries. The SEIT obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. Repair or replacement of a defective product or parts thereof does not extend the original warranty period.
EXCEPT AS SET FORTH ABOVE, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, APPLICABLE TO PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE.
OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, SEIT IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, WHETHER DIRECT OR INDIRECT, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE.
Obtaining service To obtain support for problems with your NetBotz Wireless Sensor Pod 180: 1. Note the serial number. The serial number is printed on a label located on the inside of the battery compartment lid. 2. Contact Customer Support using the information on the back cover of this manual. A technician will try to help you solve the problem by phone. 3. If you must return the product, the technician will give you a return material authorization (RMA) number.
22 NetBotz Wireless Sensor Pod 180 Installation Guide
NetBotz Wireless Sensor Pod 180 Installation Guide 23
24 NetBotz Wireless Sensor Pod 180 Installation Guide
Radio Frequency Interference Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. USA—FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. This equipment contains an intentional transmitter that has a FCC grant of authorization per Part 15C.
Schneider Electric IT Worldwide Customer Support Customer support for this product is available at no charge in any of the following ways: • Visit the SEIT web site to access documents in the Knowledge Base and to submit customer support requests. – www.apc.com Connect to localized web sites for specific countries, each of which provides customer support information. – www.apc.com/support/ Global support searching the Knowledge Base and using e-support.
