Installation and Customization NetShelter™ SX Cabinet 990-2183G-001 Publication Date: February, 2015
Schneider Electric Legal Disclaimer The information presented in this manual is not warranted by Schneider Electric to be authoritative, error free, or complete. This publication is not meant to be a substitute for a detailed operational and site specific development plan. Therefore, Schneider Electric assumes no liability for damages, violations of codes, improper installation, system failures, or any other problems that could arise based on the use of this Publication.
Table of Contents Introduction ............................................................................................................1 Unpack the Cabinet ...............................................................................................2 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction The Schneider Electric NetShelter SX cabinets are high-quality cabinets for storage of industry-standard (EIA/ ECA-310), 19 in. (483 mm) rack-mount hardware, which includes servers and voice, data, networking, internetworking, and power protection equipment. This manual covers the general installation and the customization of the NetShelter SX with Premium Datacenter Cabinets. Refer to the NetShelter SX specification manual for detailed measurements and ratings of specific models.
Unpack the Cabinet Disclaimer Schneider Electric is not responsible for damage sustained during reshipment of this product. Inspection Inspect the packaging and contents for shipping damage. Make sure that all parts are accounted for. Report any damage immediately to the shipping agent. Report missing contents, damage, or other problems immediately to Schneider Electric or your reseller. Please Recycle The shipping materials are recyclable. Save them for later use, or dispose of them appropriately.
Safety Instructions This manual contains important instructions that must be followed during the installation and customization of the cabinet. WARNING TIP HAZARD • This cabinet is easily tipped. Use extreme caution when unpacking or moving. • Use at least two people to unpack and move the cabinet. • Before moving the cabinet on its casters, load 158 kg (350 lb) of equipment into the bottom of the cabinet for extra stability.
Component Identification ns0609b Cabinet Adjustable vertical 0U accessory channel* Removable and reversible front door Removable rear split doors Nameplate (if equipped) Removable side panel with lock Key for doors and side panels Cabinet frame Vertical mounting flanges Adjustable leveling feet 1070 mm (42.13 in.) roof Hardware bag (see page 5) 1200 mm (47.24 in.) roof Casters * 1200 mm (47.24 in.
Hardware Plastic cup washer (60) M6 x 16 Phillips slot screw (60) M5 x 12 screw (4) TORX® T30/#2 Phillips tool NetShelter SX Cabinet - Installation and Customization Manual Cage nut (60) 7 mm (0.28 in.
Cabinet Installation Move the Cabinet WARNING TIP HAZARD • This cabinet is easily tipped. Use extreme caution when unpacking or moving. • Use at least two people to unpack and move the cabinet. • Before moving the cabinet on its casters, load 158 kg (350 lb) of equipment into the bottom of the cabinet for extra stability. • When moving on its casters, make sure the leveling feet are up and push the cabinet from the front or rear.
Level the Equipment The leveling feet at the corners of the equipment provide a stable base if the floor is uneven, but they cannot compensate for a badly sloped surface. Ensure the cabinet is in its intended location. Remove the front and rear doors. See “Door Removal” on page 11 for instruction. Note: Before removing the front door, unplug the ground wires and any other wire connections that may interfere with the removal of the doors.
Secure the Cabinet WARNING TIP HAZARD Secure the cabinet to the floor before installing equipment. Failure to follow these instructions can result in death, serious injury, or equipment damage. Accessory Part Number Pallet / Bolt-down provided with the Brackets cabinet AR7701 (Optional) NetShelter SX Stabilizer Plate AR7700 (Optional) Attaches externally to the rack and floor to provide additional stability.
Ground the Cabinet DANGER HAZARD OF ELECTRIC SHOCK Connection of the cabinet to building Common Bonding Network (CBN) is required. Failure to follow these instructions will result in death or serious injury. ns1617a Each cabinet should be bonded directly to a common ground using one of the designated grounding locations (two M6 threaded inserts) at the top or bottom of the cabinet. • Use a Common Bonding Network Jumper kit (for example, Listed [KDER] Panduit® RGCBNJ660PY or equivalent).
Install Side Panels, Roof and Doors na2591a Side Panels Roof ns1724b X2 10 NetShelter SX Cabinet - Installation and Customization Manual
Door Removal 1. Unlock the cabinet front door handle and open the door. ns2283a 2. Disconnect the ground wire and any other wire connections that may interfere with the removal of the doors. ns1604b 3. The hinges come apart by lifting upward and outward. Slowly lift and pull the door from the cabinet until the hinge pins on the door are free of the hinges on the cabinet frame. Door Installation 3. Connect the ground wire and any other wire connections.
Reverse the Front Door Note: The front door can be reversed so that the door opens in the other direction. This procedure assumes that initially, when facing the cabinet, the hinges are on the left and the door is opening from right. ns1758b 1. Remove the handle by removing the screw-plate. Pull the handle from the door. ns1752b 2. Disconnect the ground wire, and any other wire connections. Remove the door from the frame. See “Door Removal” on page 11 for more information. ns1824a 3.
ns1779b ns1766b 6. Locate the lock handle. Remove the cam screw, cam washer, and cam. Rotate the cam washer 90 degrees, and the latch 180 degrees. Install the handle on the door. 7. Remove the nameplate (if equipped) from the door. Install the nameplate at the location shown in the illustrations below. 307 mm (12 in.) ns1612b ns2010a 300 m m 375 m (11.8 in.) (6 m (14 .8 in.
Equipment Installation Note: NetShelter SX cabinets are intended for use with Listed equipment. If you install un-Listed equipment, you should evaluate the safety of your configuration. Adjust the Vertical Mounting Flanges Vertical mounting flanges come factory-installed at 737 mm (29 in.), the proper location for use with rack-mountable equipment. The mounting flanges are adjustable towards the front or the rear of the cabinet to accommodate different rails or equipment with other depths.
Vertical Mounting Flange Adjustment WARNING FALLING EQUIPMENT Remove all equipment installed on the vertical mounting flanges before performing any adjustments. Failure to follow these instructions can result in serious injury or equipment damage. 1. Use the provided TORX T30 tool to loosen the top, middle, and bottom TORX screws holding the vertical mounting flange in place. The brackets, all held in place by the TORX screws, will now be loose.
3. To align the vertical mounting flange, note the symbol (for example, a diamond) visible through one of the three holes. Only one symbol will be visible. In the factory standard position, a circle symbol is visible. Make sure the same symbol is visible through the corresponding hole at both the top and the bottom of the flange. ns1623a 2. Move the mounting flange to the desired location. Vertical mounting flanges adjust in 6 mm (1/4 in.) increments. 4.
Install the Equipment WARNING TIP HAZARD • This cabinet is easily tipped. Make sure you have secured the cabinet to the floor before installing equipment. • Install the heaviest equipment first and toward the bottom of the cabinet to prevent the cabinet from becoming top-heavy. • Do not extend equipment on sliding rails until you have installed 158 kg (350 lb) of equipment into the bottom of the cabinet for stability or until you have installed the stabilizer plate or bolt-down brackets.
Remove the Cable Cutout Covers For NetShelter SX 750 mm (29.5 in.) wide cabinets that include equipment requiring side airflow, on the side of the cabinet nearest the air intake for the equipment (right side in the example below), remove the cable cutout covers from the front vertical mounting flange. Reinstall the covers in the cable cutout holes on the rear vertical mounting flange on the same side of the cabinet.
Specifications General specifications for SX cabinets - for detailed dimensions and weights refer to the NetShelter SX Specification manuals. Width Height by “U” dimension Depth Height (U) Height (mm) Height (in.) Width (mm) Height (in.) Depth (mm) Depth (in.) 24U 1199 47.2 600 23.6 1070 42.1 42U 1991 78.4 700* 27.6 1200 47.2 45U 2124 83.6 750 29.5 48U 2258 88.9 50U 2347 92.4 52U 2436 95.9 54U* 2525 99.
Limited Factory Warranty The limited warranty provided by Schneider Electric in this Statement of Limited Factory Warranty applies only to Products you purchase for your commercial or industrial use in the ordinary course of your business. Terms of Warranty Schneider Electric warrants its products to be free from defects in materials and workmanship for a period of five years (two years in Japan) from the date of purchase.
Worldwide Customer Support Customer support for this or any other product is available at no charge in any of the following ways: • Visit the Schneider Electric Web site to access documents in the Schneider Electric Knowledge Base and to submit customer support requests. – www.schneider-electric.com (Corporate Headquarters) Connect to localized Schneider Electric Web sites for specific countries, each of which provides customer support information. – www.schneider-electric.
