Specifications
Table Of Contents
- Product Description
- Safety
- Product Overview
- Specifications
- Installation
- Connect Equipment to the UPS
- 1 . Connect equipment to the outlets on the rear panel of the UPS. Do not use extension cords, pl...
- 2 . Connect the UPS to the building utility power. Connect the UPS to a two-pole, three-wire, gro...
- 3 . Press the On/Off button on the front panel of the UPS to apply power to the unit and all conn...
- 4 . To use the UPS as a master on/off switch, turn on all the equipment that is connected to the ...
- Rear Panel Features
- Display Interface
- Overview
- Using the display interface
- Standard menus
- • Operating mode
- • Switched Outlet status, On or Off
- • Efficiency of the UPS
- • Information about the load
- • Battery capacity
- • Estimated runtime
- • Input and output voltage and frequency
- • Information about the last transfer to battery power
- • Self-test results
- • Language
- • Local power quality: Good, Fair, Poor
- • Choose Standard or Advanced menus
- • LCD Display mode, Always On or Power-Saving
- • Audible alarms
- • Reset to Factory Defaults
- • Unit model number
- • Serial number
- • Battery installation date
- • Suggested battery replacement date
- • Replacement Battery Cartridge model number
- • UPS firmware version
- Advanced menus
- UPS Settings
- Start-up Settings
- General Settings
- • 127 Vac
- • 130 Vac
- • 133 Vac
- • 136 Vac
- • 253 Vac
- • 257 Vac
- • 261 Vac
- • 265 Vac
- • 97 Vac
- • 100 Vac
- • 103 Vac
- • 106 Vac
- • 196 Vac
- • 200 Vac
- • 204 Vac
- • 208 Vac
- • High: The UPS will go on battery power more often to provide the cleanest power supply to the c...
- • Low: The UPS will tolerate more fluctuations in power and will go on battery power less often.
- • Never
- • Start-up only
- • Frequency of test (days)
- Main Outlet Group and the Switched Outlet Group
- Overview
- Using the Main Outlet Group and the Switched Outlet Group
- Customize the Main Outlet Group and the Switched Outlet Group
- Network Management Card Settings
- Emergency Power Off
- Service
- 1 . Review the Troubleshooting section of the UPS manual to eliminate common problems.
- 2 . If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com.
- a. Note the model number and serial number, located on the rear of the unit, and the date of purc...
- b. Call APC Customer Support and a technician will attempt to solve the problem over the phone. I...
- c. If the unit is under warranty, the repairs are free.
- d. Service procedures and returns may vary internationally. Refer to the APC Web site for country...
- 3 . Pack the unit in its original packaging. If this is not available, refer to www.apc.com to ob...
- a. Pack the unit properly to avoid damage in transit. Never use foam beads for packaging. Damage ...
- b. For the UPS, always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department ...
- c. Internal batteries may remain connected in the XLBP during shipment (if applicable, not all un...
- 4 . Write the RMA# provided by Customer Support on the outside of the package.
- 5 . Return the unit by insured, pre-paid carrier to the address provided by Customer Support.
- Transport the unit
- APC Worldwide Customer Support
- LIMITED WARRANTY
Smart-UPS 750/1000/1500/2200/3000 VA 120/230 Vac Tower 6
Advanced menus
The Advanced menus provide additional options for the UPS and are available only if the display
interface is configured to use the Advanced menus.
About Display information about this unit:
• Unit model number
• Serial number
• Battery installation date
• Suggested battery replacement date
• Replacement Battery Cartridge model number
• UPS firmware version
Menu General Functions
Status View detailed information about the UPS:
• Energy meter
• Load current
• Status of the Switched Outlet Group
• Battery voltage
Configuration Configure advanced settings for the UPS:
• Main and Switched Outlet Group—delays and settings
• High and lower transfer points
• Sensitivity settings
• Date of last battery replacement
Control Control the Main and Switched Outlet Group to turn on,
turn off, or reboot.
Test & Diags Perform a UPS alarm test or a runtime calibration test.
Log View the event log for information about any changes to
the UPS and any faults.
About View information about the unit:
• Hardware version
• Software version
• NMC information (if applicable)
Menu General Functions