PS6003rm2u shipboard Operation Powerstar Inc CAGE 0ZAP8 800-209-5556 +1301-948-0713 info@powerstarinc.com www.powerstarinc.
Contents Overview .......................................................................... 1 About the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview About the UPS The APC® by Schneider Electric Smart-UPS® X is a high performance uninterruptible power supply (UPS). It provides protection for electronic equipment from utility power blackouts, brownouts, sags, and surges; small utility fluctuations and large disturbances. The UPS also provides battery backup power until utility power returns to safe levels or the batteries are fully discharged. The Smart-UPS X UPS has both high voltage (200-240 V) and low voltage (100-127 V) models.
Rear panel Smart slot UPS input Controllable Outlet Group 3 External battery pack connector Ground screw Controllable Outlet Group 1 EPO connector Serial port Controllable Outlet Group 2 USB port 2000 VA Low Voltage Specifications Operating Conditions This unit is intended for indoor use only. Select a location sturdy enough to support the weight of the UPS and External Battery Packs (XLBP).
Installation UPS For UPS installation information, see the Smart-UPS X 2000-3000 VA Quick-Start that is included with the UPS. The guide is also available on the enclosed CD and the APC Web site at www.apc.com. Network Management Card For installation information, see the user manual provided with the Network Management Card (NMC). The user manual is also available on the APC Web site at www.apc.com.
Operation Connect Equipment to the UPS Note: The UPS will charge to 90% capacity in the first three hours of normal operation. Do not expect full battery runtime capability during this initial charge period. 1. Connect equipment to the outlets on the rear panel of the UPS. Do not use extension cords, plug equipment directly into the UPS. 2. Connect the UPS to the building utility power. Connect the UPS to a two-pole, three-wire, grounded source only. 3.
Display Interface Overview Online indicator UPS Output On/Off button On Battery indicator Fault indicator Replace Battery indicator Display screen UP and DOWN buttons ENTER button ESCAPE button APC By Schneider Electric su0343a Using the display interface Use the UP and DOWN to scroll through the main menu options. Press ENTER to view the sub-menus under each main menu option. Press ESCAPE to exit a sub-menu and return to a main menu.
Main Menu Overview Standard Load meter (kWh) Configuration Control Test & Diagnostics Statistics Logs 6 Advanced x Last transfer to battery power information x x Battery charge and estimated run time x x Battery voltage x Number of external battery packs x Internal battery temperature x Run time calibration test results x x Self-test results x x Status of the switched outlet group(s): On, Off, Sleep, Reboot, Turning On, Turning Off x Smart Slot information (if applicable) x La
Main Menu About Overview General information about the UPS, including: model numbers, output voltage setting, serial number, manufacture date, replacement battery cartridge information, firmware versions, and suggested battery replacement date.
Configuration UPS Settings Start-up Settings Use the display interface to configure these settings at initial start-up. The unit will prompt for a response to each setting, if not response is given, it will use the default setting. Note: The until will not turn on until all of these settings are entered. Function Factory Default Options Description Language English • English • French* • German* • Spanish* • Italian* • Portuguese* The language for the display interface.
General Settings Configure these settings at any time, using the display interface, APC PowerChute® software, or a network management card.
Function Factory Default Options Date of Last Battery Replacement Date set at factory Reset this date when the battery module is replaced. Audible Alarm On 10 On/Off Description The UPS will never beep if all audible alarms are set to Off or when the display buttons are pressed.
Switched Outlet Groups Overview The Switched Outlet Groups can be configured to independently turn off, turn on, shut down, put to sleep, and reboot connected equipment.
Function Factory Default Options Description Turn Off Delay 90 sec Set the value in seconds The amount of time that the Switched Outlet Groups will wait between receiving the command to turn off and the actual shut down. Reboot Duration 8 sec Set the value in seconds The amount of time that the Switched Outlet Groups must remain off before it will restart.
Emergency Power Off EPO Overview The Emergency Power Off (EPO) option is a safety feature that will immediately disconnect all connected equipment from utility power. The UPS will immediately shut down and will not switch to battery power. Connect each UPS to the EPO switch, even if the UPS units are used in parallel. The UPS must be manually restarted to reapply power to connected equipment. Press ON/OFF on the front panel of the unit. 1.
Troubleshooting Problem and Possible Cause Solution The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button to turn on the UPS. The UPS is not connected to utility power. Ensure that the power cable is securely connected to the unit and to the utility power supply. There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately.
Service and Support Service Contact Powerstar for Replacement Battery Packs. Your unit may use Powerstar Premium Long Life Cells. If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the manual to eliminate common problems. 2. If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com. a. Note the model number and serial number and the date of purchase.
Smart-UPS Factory Warranty LIMITED WARRANTY Powerstar Inc provides the warranty for this unit. contact Powerstar for Repair American Power Conversion (APC) warrants its Smart-UPS (Products) to be free from defects in materials and workmanship for a period of three (3) years, excluding the batteries, which are warranted for two (2) years from date of purchase. APC's obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products.
© 2009 APC by Schneider Electric. APC, the APC logo are owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation, or their affiliated companies. All other trademarks are property of their respective owners.