Owner`s manual

ManualsBrandsAPC Manualsbatteries & accessoriesSmart-UPS Ultra Battery Pack 48V

UXBP

Battery Pack

Models: UXBP24, UXBP24L, UXABP48

• Do not move the UXBP with its batteries installed. Doing so may

result in damage to the Battery Pack and/or a shock hazard.

• Install only factory-authorized batteries in the UXBP. Improper

batteries may result in a hazardous chemical spill and/or a shock

hazard.

3. Presentation

3.1 UXBP front

UXBP Battery Pack

The UXBP contains either two (UXBP24L) or four (UXBP24,

UXABP48) user-replaceable, sealed lead-acid batteries and the associated

cables and connectors.

1. Front panel/Battery door

The front panel of the Battery Pack provides access for battery installation

and replacement. Refer to Section 4 when installing or replacing batteries.

2. Battery internal coupler

These four couplers connect the UXBP’s replaceable internal batteries. See

Section 4.

3. Batteries

The Battery Pack contains either two (UXBP24L) or four (UXBP24,

UXABP48) nominal 12 Vdc sealed lead-acid batteries. Use only factory-

authorized batteries in the UXBP!

3.2 UXBP rear

1. Battery Pack rear panel coupler

Additional UXBP Battery Packs are connected to this coupler. Refer to

Section 4.5 for information on making connections with this coupler.

2. In-line Battery Pack coupler

This coupler connects the Battery Pack to the UPS or to the rear panel

coupler on another matching Battery Pack.

1. Introduction

The UXBP is a large Battery Pack module designed to be used with a Smart-

UPS system to provide a significant increase in on-battery runtime for your

protected equipment.

For complete information on the Smart-UPS system, refer to the Owner’s

Manual that came with your UPS.

Note: If you are installing your Smart-UPS system for the first time, be

sure to read the Smart-UPS Owner’s Manual first. Set up your

UPS system before installing the UXBP.

2. Safety!

CAUTION!

• Use the UXBP only with a UPS that is properly installed according to

the UPS Owner’s Manual and connected only to a two-pole, three-wire

grounding mains receptacle. The receptacle must be connected to

appropriate branch protection (fuse or circuit breaker). Connection to

any other type of receptacle may result in a shock hazard and may

violate local electrical codes.

• Avoid installing the UXBP in locations where there is water or

excessive humidity.

• Do not allow water or any foreign object to get inside the UXBP. Do

not put objects containing liquid on or near the unit.

• To reduce the risk of overheating the UXBP, avoid exposing the unit to

the direct rays of the sun. Avoid installing the unit near heat emitting

appliances such as a room heater or stove.

Installation Instructions

Summary of content (4 pages)

PAGE 1
UXBP Battery Pack • Do not move the UXBP with its batteries installed. Doing so may result in damage to the Battery Pack and/or a shock hazard. • Install only factory-authorized batteries in the UXBP. Improper batteries may result in a hazardous chemical spill and/or a shock hazard. 3. Presentation 3.
PAGE 2
4. Installation 4.1 Receiving inspection When you remove the UXBP from its shipping container, inspect it for damage that may have occurred in transit. Immediately notify the carrier and place of purchase if any damage is found. The packing materials are made from recyclable materials and should be saved for reuse or disposed of properly. • CAUTION — A battery can present a risk of electrical shock and high short circuit current. When replacing batteries, remove wrist watches and jewelry such as rings.
PAGE 3
Table 2 - UXABP48 Battery Pack Voltage 4. UXBP24L UXBP24 and UXABP48 - If you have a UXBP24 or UXABP48, slide the second battery all the way to the rear of the cabinet beside the first battery. Battery Pack Voltage Battery Pack Status 45.0 Vdc - 57.0 Vdc Ready to Install 0.0 Vdc - 45.0 Vdc Miswired or Bad Battery When the Battery Pack Status is “Ready to Install,” complete the final steps of the installation.
PAGE 4
5. Storing the Battery Pack 7.3 Physical UXBP24L UXBP24/UXABP48 The Battery Pack should be stored in a covered location and with its batteries in a fully-charged state (reports 100% capacity to the UPS). Size (H´W´D): 31.0 x 44.7 x 75.4 cm 31.0 x 44.7 x 75.4 cm (12.2 x 17.6 x 29.7 in.) (12.2 x 17.6 x 29.7 in.) In extended storage, use the UPS to refresh the Battery Pack every six months in environments where the temperature is –15 to +30 °C (+5 to +86 °F).