Operating instructions

ManualsBrandsAPC ManualsConsumer electronicsSmartSlot AP9604SR

Thank You!

Thank

ou for selectin

this American Power Conversion SmartSlot

Series Rela

I/O Module UPS accessor

. It has been desi

ned for man

ears of reliable, maintenance-free service. Please read this manual! It

provides installation and operatin

instructions that will help

et the

most from

our accessor

. Save this manual! It includes important

instructions for the safe installation of

our accessor

. Further, it includes

instructions for obtainin

factor

service.

Radio frequency interference

Warning:

Chan

es or modifications to this unit not expressl

approved

the part

responsible for compliance could void the users authorit

operate the equipment.

Note:

This equipment has been tested and found to compl

with the limits

for a Class B di

ital device, pursuant to Part 15 of the FCC Rules. These

limits are desi

ned to provide reasonable protection a

ainst harmful inter-

ference in a residential installation. This equipment

enerates, uses and

can radiate radio frequenc

ener

and, if not installed and used in accor-

dance with the instructions, ma

cause harmful interference to radio com-

munications.

However, there is no

uarantee that interference will not occur in a partic-

ular installation. If this equipment causes interference to radio or televi-

sion reception, which can be determined b

turnin

the equipment off and

on, the user is encoura

ed to tr

to correct the interference b

one or more

of the followin

measures:

• reorient the receiving antenna

• increase the separation between the equipment and the receiver

• connect the equipment into an outlet on a circuit different from

that to which the receiver is connected

• consult the dealer or an experienced radio/TV technician for

help.

Shielded communications interface cables must be used with this product

to ensure compliance with Class B FCC limits.

This di

ital apparatus does not exceed the Class B limits for radio noise

emissions from di

ital apparatus set out in the Radio Interference Re

ula-

tions of the Canadian Department of Communications.

Reproduction in whole or in part without written permission is prohibited. SmartSlot

and the stylized APC logo are trademarks of APC. All other trademarks are property of

their respective owners.

Summary of content (17 pages)

PAGE 1
Thank You! Thank you for selecting this American Power Conversion SmartSlot Series Relay I/O Module UPS accessory. It has been designed for many years of reliable, maintenance-free service. Please read this manual! It provides installation and operating instructions that will help you get the most from your accessory. Save this manual! It includes important instructions for the safe installation of your accessory. Further, it includes instructions for obtaining factory service.
PAGE 2
Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Operating Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 Final Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
1. Introduction The APC SmartSlot Relay I/O Module is a SmartSlot Series UPS accessory that provides the following features: • UPS status information presented as six form C contact closures • UPS control and testing by contact closure inputs • Screw terminal connectors for easy integration into various management systems. Description The SmartSlot Relay I/O Module consists of a printed circuit board assembly (right below), and an accessory connection board (left below).
PAGE 4
2. Configuration Switch setting The SmartSlot Relay I/O Module requires configuration before testing, final installation, and use. Note: While the SmartSlot Relay I/O Module has a four position DIP configuration switch (marked CONFIG SWITCH on the printed circuit board— see figure 1), only position 1 is used. The other switches must be left in the off position. Move the switch up for ON and down for OFF. Configuration 1 is intended for use with UPSs that do not include a bypass feature (like Smart-UPS).
PAGE 5
Input/Output Configurations Input/ Output Configuration 1 (CONFIG SWITCH 1 off) Configuration 2 (CONFIG SWITCH 1 on) Input #1 Turn the UPS on Input #2 Turn the UPS off Input #3 Start UPS self-test Input #4 Shut down the UPS (when onbatter except during a self-test or run time calibration) Put the UPS in bypass (if available on the UPS) Output #1 The UPS is on-battery (e.g.
PAGE 6
3. Operation Check Check the operation of the SmartSlot Relay I/O Module before final installation. Note: The UPS will not protect the load during this procedure. 1. Check the output relays by temporarily installing the SmartSlot Relay I/O Module into the SmartSlot. See section 4 for information on installing the SmartSlot Relay I/O Module in the SmartSlot. Attach the supplied screw terminal connection board. 2. Turn on the UPS. Wait for a few seconds for the SmartSlot Relay I/O Module to initialize.
PAGE 7
4. Operating Considerations Note: While the SmartSlot Relay I/O Module output contacts are voltage free, connected equipment may present hazardous voltages. Use care during installation. Please note the following SmartSlot Relay I/O Module characteristics when making system integration decisions: • The coils for all output relays are normally energized.
PAGE 8
5. Final Installation 1. Use either the supplied accessory connection board or a male 25 pin D connector (not supplied) to make connections to the SmartSlot Relay I/O Module. To use a male 25 pin D connection see section 6 for the connector pinout. To use the supplied accessory connection board see figure 2 below. Note the use of tie wraps to secure the connecting wires to the board. The connection board accepts 16 AWG to 28 AWG wires. Figure 2, accessory connection board wire dress 2. 3. 4.
PAGE 9
shown in figure 3. Note that the sides of the printed circuit board align with the locating slots in the sides of the SmartSlot. The SmartSlot may be oriented horizontally or vertically in the host device. The host device may be on or off. 5. Use a #2 Phillips head screwdriver to remove the two screws retaining the SmartSlot cover on the host device. Keep the screws handy for step 7 below. Keep the SmartSlot cover for future use. Figure 3, Relay I/O Module installation 6.
PAGE 10
6. Connection Strategies The alarm outputs of the SmartSlot Relay I/O Module can be connected in a number of ways to meet the needs of the management system. Both N. O. or N. C. systems are accommodated in any combination of AND or OR configurations. It is possible, then, to combine SmartSlot Relay I/O Module alarm outputs to form compound outputs like replace battery OR fault, or on-battery AND low battery. See figure 4.
PAGE 11
7. Dry Contact I/O Pinout 13 12 11 10 9 8 7 6 5 4 3 2 1 25 24 23 22 21 20 19 18 17 16 15 14 Function Pin Function Pin N. O. output #1 (NO1) 1 N. O. output #2 (NO2) 14 Output #1 common 2 Output #2 common 15 N. C. output #1 (NC1) 3 N. C. output #2 (NC2) 16 N. O. output #3 (NO3) 4 N. O. output #4 (NO4) 17 Output #3 common 5 Output #4 common 18 N. C. output #3 (NC3) 6 N. C. output #4 (NC4) 19 N. O. output #5 (NO5) 7 N. O.
PAGE 12
8.
PAGE 13
9.Troubleshooting Problem Possible Cause Solution The SmartSlot relay I/O Module does not respond to control inputs. Insufficient setup or hold times. Configure controlling equipment to provide at least one second of alarm hold. See section 4. Invalid or intermittent alarms. Poor contact at either the dry contact I/O connector or the accessory connection board. Correct poor contact conditions. Tighten all connector screws. Alarms always on or will not come on. Relay welded.
PAGE 14
10. Service If the SmartSlot Relay I/O Module requires service: 1. Check the SmartSlot Relay I/O Module using the troubleshooting chart in section 9 before calling for service. 2. Note the model number of the SmartSlot Relay I/O Module, the serial number, and the date purchased. See the back cover of this manual for the correct telephone number and call customer service. A technician will ask you to describe the problem and help solve it over the phone, if possible, or will give you an RMA#.
PAGE 15
11. Specifications Electrical SmartSlot specification compatible Operating voltage: 16–27 Vdc Operating current draw: 70 mAdc Physical Size (H x W x D): 4 x 4 x 1.5 inches (10.2 x10.2 x 3.8 cm) Weight: 0.3 lb. (140 gm) Shipping weight: 0.7 lb. (320 gm) Environmental Operating elevation (storage): 0 to 3,000 m (0 to 15,000 m) Operating temp.
PAGE 16
12.Declaration of Conformity Application of Council Directives: 89/336/EEC Standards to Which Conformity is Declared: EN55022, EN50082-1 Manufacturer’s Name: American Power Conversion 132 Fairgrounds Road West Kingston, RI 02892 USA Importer’s Name and Address: Type of Equipment: SmartSlot Relay I/O Module Model Number: AP9610 Serial Numbers: A95040000001–A961299999999 Year of Manufacture: 1995, 1996 I, the undersigned, hereby declare that the equipment specified above conforms to the above directive(s).
PAGE 17
Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from APC or an APC service center.