MADE BY APELABS.
APP DOWNLOAD http://bit.
Deutsch Sicherheitshinweise › Während des Betriebs des WAPP und während des Ladevorgangs entsteht Wärme. Sorgen Sie daher für ausreichend Belüftung und decken den WAPP nicht ab. › Benutzen Sie den WAPP nicht in Bereichen, in denen der Gebrauch von Funkgeräten verboten ist. Allgemeines › Der WAPP funktioniert zusammen mit der WAPPAPP die im Google Play Store und im Apple AppStore heruntergeladen werden. › Mit der APP können ApeLabs Lampen gruppiert und gesteuert werden.
Deutsch Betrieb Ein-/Ausschalten › Drücken Sie den Taster an der Rückseite des WAPP für ca. 1 Sekunde. › Zum Ausschalten drücken Sie den Taster erneut für ca. 1 Sekunde. Die Verzögerung beim Ein- und Ausschalten dient als Sicherung, um nicht ungewollt das Gerät zu aktivieren. Verbinden mit der App Vor der ersten Benutzung muss der WAPP mit der APP verbunden werden. So ist sichergestellt, dass keine anderen Smartphones mit installierter APP eine Verbindung aufbauen und Geräte steuern können.
Deutsch Bedeutung der Anzeigen › Funk-LED an: Der Funkchip für die Kommunikation mit den ApeLabs-Geräten ist aktiv. › Bluetooth-LED aus: Gerät wartet auf eine Verbindung zur APP › Bluetooth-LED an: Verbindung mit der APP ist aktiv. › Akku-LED grün leuchtend: Akku vollständig geladen oder Batteriebetrieb mit ausreichend geladenem Akku. › Akku-LED grün blinkend: Akku wird aufgeladen › Akku-LED orange: Akku fast leer › Akku-LED rot: Akku leer. › Akku-LED rot blinkend: Kein Akku eingebaut oder defekt.
Deutsch Erweiterte Steuerung Steuerung über einen DMX Controller › Verbinden Sie den WAPP-Transceiver per DMX-Kabel mit DMX Controller. › Stellen sie sicher, dass die APP mit dem WAPP verbunden ist. › Wählen sie eine zu steuernde Gruppe aus. › Wählen Sie im Menü „Control-Mode“ den „DMX-Transmitter“ aus. › Im Menü „Lamp Setup“ können den ApeLabs Geräten DMX-Adressen zugewiesen werden. Empfangen von DMX-Daten per Funk › Verbinden Sie den WAPP-Transceiver per DMX-Kabel mit dem Zielgerät.
Deutsch Fehlerbehebung Problem Mögliche Ursache Lösung Keine Verbindung mit der APP W-APP ist nicht mit der APP gekoppelt Menü „Connection“ aufrufen, WAPP auswählen und den Anweisungen folgen Bluetooth deaktiviert Aktivieren Sie Bluetooth auf Ihrem Smartphone/Tablet Schalten Sie den WAPP aus und wieder an und starten Sie ihr Smartphone/Tablet neu.
Deutsch Problem Gruppen-LEDs blinken abwechselnd Mögliche Ursache Lösung 18V Netzteil anAkku komplett stecken. Ladung leer beginnt evtl. erst nach einigen Minuten. Gerät im Bootloa- Drücken Sie die Power-Taste für der-Modus einige Sekunden und versuchen Sie den WAPP neu zu starten. WAPP-Firmware fehlt 6 Starten Sie die APP, wählen Sie den Menüpunkt „WAPP-Update“ und spielen sie die aktuelle Firmware auf.
Deutsch Recycling Der WAPP sowie alle im Lieferumfang enthaltenen Elektronikteile dürfen gemäß europäischen Richtlinien nicht über den Hausmüll entsorgt werden.
English Safety Instructions › Heat is generated during operation of the WAPP and during charging. Ensure an adequate ventilation and do not cover the WAPP. › Do not use the WAPP in areas where the use of radio equipment is prohibited. General › The WAPP works in conjunction with the WAPP APP, which is downloaded from the Google Play Store and the Apple App Store (NOT RELEASED – STATUS 02/2019 – PLEASE CHECK LATER AGAIN.) › With the APP, Ape Labs lamps can be grouped and controlled.
English Operation Turning on / off › Press the button on the back of the WAPP for approx. 1 second. › To switch off press the button again for approx. 1 second. The delay when switching on and off serves as a backup so as not to accidentally activate the device. Connect with the app Before of the first use, the WAPP must be connected to the APP. This ensures that no other smartphones with an installed APP can connect and control devices. The APP guides you through the connection process.
English Reset to factory settings Hold the button on the rear side for about 8 seconds until the group LEDs flash alternately. The device is now in „bootloader mode“. The Bluetooth-icon of the APP changes to yellow. In the menu item „WAPP update“, the current software can be re-recorded. Meaning of Status LEDs › Radio LED on: The wireless chip for communication with the Ape Labs devices is active.
English › Battery LED green flashing: Battery is charging › Battery LED orange: Battery almost empty › Battery LED orange: Battery almost empty › Battery LED red: Battery empty › Battery LED flashing red: No battery installed or defective. › The groups that are activated in the APP are displayed on the WAPP as „Group 1, 2, 3 and 4“.
English Advanced control Control by a light desk via DMX › Connect the WAPP transceiver to a lighting console via DMX cable. › Make sure the APP is connected to the WAPP. › Select a group to control. › In the „Control Mode“ menu, select the „DMX Transmitter“. › In the menu „Lamp Setup“ the Ape Labs devices can be assigned DMX addresses. Receive DMX data by radio › Connect the WAPP transceiver to the target device via DMX cable. › Make sure the APP is connected to the WAPP.
English Troubleshooting Problem Possible cause Solution No connection with the APP WAPP is not coupled with the APP. Call up the „Connection“ menu, select WAPP and follow the instructions. Bluetooth disabled. Activate Bluetooth on your phone. WAPP or APP crashed. Turn the WAPP off and on again and restart your phone. WAPP will Button pressed to not turn on short. Press button and hold for 1 second. Battery completely empty. Plug in 18V power adapter. Charge may start after a few minutes.
English Group device in bootloaLEDs der mode. alternately flashing 14 Press the power button for a few seconds and try to restart the WAPP. WAPP firmware missing . Activate Bluetooth on your phone. WAPP or APP crashed. Start the APP, select the menu item „WAPP Update“ and put the current firmware on it.
English Recycling The WAPP and all electronic parts included in the delivery must not be disposed of with household waste in accordance with European directives.
Ape Labs GmbH Landwehrstr. 26 97249 Eisingen GERMANY Tel. +49 (0)9306-985392-0 Fax. +49 (0) 9306-985392-1 info@apelabs.com www.apelabs.