Installation Guide

15
3. Point W - Discharge water connection:
Tubing color: Black tubing. Connect the BLACK tubing from the RO to the Drain Saddle.
Fitting type: Quick Connect. Simply push Black tubing into the Quick Connect Fitting.
No Insert, Sleeve or Nut needed here. See Fig. 10A (Page 12)
4. Point A - System water inlet (to Stage-1 pre-filter) connection:
Tubing color: Red tubing. Connect the RED tubing from the Feed Water Valve to the RO’s stage -1
pre-filter.
Fitting type: Quick Connect fitting See Fig. 10A (Page 12). Simply push the Red tubing into the QC
fitting. No Inserts, Sleeves or Nuts are needed to secure the connection. No Teflon tape
needed here.
5. Point H - Stage-6 FI-ES-TCR-QC filtered water to faucet connection:
Tubing color: Clear tubing. Connect the CLEAR tubing from the faucet base stud to the Stage-6 filter’s
outflow end at point H. (See “Flow -->” arrow on the filter is the output to faucet at Point Z.)
Fitting type: Quick Connect: Simply push the Clear tubing into the QC fitting. No Inserts, Sleeves or
Nuts are needed to secure the connection. No Teflon tape needed here.
6. Point G - Stage-5 UV Light T-fitting connection:
Tubing color: Yellow tubing. Connect the YELLOW tubing to Stage-5 UV housing T-fitting.
Fitting type: Quick Connect: Please remove the End Plug first, and then simply push the Yellow tubing
into the QC fitting. No Inserts, Sleeves or Nuts are needed to secure the connection. No
Teflon tape needed here.
7. Point Y - Tank’s input & output connection:
Prepare tank: See Fig.12. Apply 6-8 wraps of Teflon tape to tank’s threaded Output stem on top of tank
(remove rubber cap if there is one). Screw tank Valve onto Output stem.
Tubing color: Yellow tubing. Connect the YELLOW tubing from Stage-5 T-fitting to the tank’s valve.
Fitting type: Quick-Connect fitting on ball valve. Simply push Yellow tubing into valve port.
Standard 4-gallon Tank Diagram:
Fig. 12
Tank Ball Valve
OFF Position ON Position
15
3
. Point W - Discharge water connection
:
Tubi
ng
color: Black tubi
ng
. Connect the BLACK tubi
ng
from the RO to the Drain Saddle.
F
itting type: Quick Connect. Simply push Black tubing into the Quick Connect Fitting.
No Insert
,
Sleeve or Nut needed here. See Fig. 10A
(
Page 12
)
4. Point A - System water inlet (to Stage-1 pre-
f
ilter) connection
:
Tubing color: Red tubing. Connect the RED tubing from the Feed Water Valve to the RO’s stage -1
pre-
f
ilter.
F
itting type: Quick Connect
f
itting See Fig. 10A
(
Page 12
)
. Simply push the Red tubing into the QC
f
itting. No Inserts, Sleeves or Nuts are needed to secure the connection. No Te
f
lon tape
n
eeded
h
e
r
e
.
5. Point H - Stage-6 FI-ES-TCR-QC
f
iltered water to
f
aucet connection
:
Tubing color: Clear tubing. Connect the CLEAR tubing from the faucet base stud to the Stage-6 filter’s
outflow
e
n
d
a
t
w
po
i
nt H.
(
See “Flow -
->
”
arrow on the
f
ilter is the out
pu
t to
f
aucet at Point Z
.)
F
itting type: Quick Connect: Simply push the Clear tubing into the QC
f
itting. No Inserts, Sleeves o
r
N
uts are needed to secure the connection. No Te
f
lon tape needed here.
6. Point G - Stage-5 UV Light T-
f
itting connection
:
Tubing color: Yellow tubing. Connect the YELLOW tubing to Stage-5 UV housing T-
f
itting.
F
itting type: Quick Connect: Please remove the End Plug
f
irst, and then simply push the Yellow tubing
i
nto the QC
f
itting. No Inserts, Sleeves or Nuts are needed to secure the connection. No
Te
f
lon tape needed here.
7. Point Y - Tank’s input & output connectio
n:
P
repare tank: See F
i
g.12. Apply
6
-8 wrap
s
of Teflon tape to tank’s threaded Output stem on top of tank
p
(
remove rubber cap i
f
there is one). Screw tank Valve onto Output stem.
Tubi
ng
color: Yellow tubin
g.
Connect the YELLOW tubi
ng
from St
ag
e-5 T-fittin
g
to the tank’s valve.
F
itting type: Quick-Connect
f
itting on ball valve. Simply push Yellow tubing into valve port.
Standard 4-gallon Tank Diagram
:
F
i
g. 12
T
a
nk B
a
ll V
a
lv
e
O
FF P
os
iti
on
ON
Positio
n