SOFTENER SERIES INSTALLATION INSTRUCTION & OWNER’S MANUAL Ver 2.0 www.FreeDrinkingWater.
Please keep this Owner’s Manual for future reference. It contains useful information on how to maintain and care for your APEC Whole House Water Softener System Thank you for choosing APEC Whole House Water Filter System. Please read and become familiar with instructions and parts needed before proceeding with the installation. General Installation/Operation/Maintenance Requirements • Use a Licensed Plumber to Install this product.
Table of Contents System Installation Kit ......................................................................................... 02 Installation ................................................................................................................... 03 Bypass Operation ................................................................................................ 05 Setting Time of Day ............................................................................................
System installation kit Bypass Valve X1 Softener Tank X1 Salt Tank X1 Salt Tank Tubing X1 V3007-02LF kit includes: Brass Sweat Adapter Kit X2 1” Quick Connect X2 Plastic Split Rings X2 Rubber O-rings X2 V3007 kit includes: Elbow Solvent Kit X2 1” Quick Connect X2 Plastic Split Rings X2 Rubber O-rings X2 Drain line adapter: Option 1 Option 2 2
Installation Brine tank Top view Brine tank installation SITE REQUIREMENTS: The control valve, fittings and/or bypass are designed to accommodate minor plumbing misalignments but are not designed to support the weight of a system or the plumbing. Do not use Vaseline, oils, other hydrocarbon lubricants or spray silicone anywhere. A silicon lubricant may be used on black o-rings but is not necessary. Avoid any type of lubricants, including silicone, on red or clear lip seals.
4. Do not locate unit where it or its connections (including the drain and overflow lines) will ever be subjected to room temperatures under 34° F. 5. The use of resin cleaners in an unvented enclosure is not recommended. 6. INLET/OUTLET PLUMBING: Connect to a supply line downstream of outdoor spigots. Install an inlet shutoff valve and plumb to the unit’s bypass valve inlet located at the right rear as you face the unit.
bottom of overflow fitting. Do not “tie” this tube into the drain line of the control valve. Overflow line must be a direct, separate line from overflow fitting to drain, sewer, or tub. Allow an air gap as per the drain line instructions. IMPORTANT: Never insert a drain line directly into a drain, sewer line, or trap. Always allow an air gap between the drain line and the wastewater to prevent the possibility of sewage being back-siphoned into the softener.
Set Water Hardness Step 1i Step 4i To enter Installer Display press NEXT and simultaneously for about 5 seconds and release. Next Regeneration Time (hour): Set the hour of day for regeneration using or . The default time is 2:00. This display will show “REGEN on 0 GAL” if “on 0” is selected in Set Regeneration Time Option in Softener System Setup or Filter System Setup. Step 2i Hardness: Set the amount of influent hardness using or .
Regeneration & Error Screens, Button Operation & Function Button Operation and Function Regen Screen Scrolls to the next display. Displays the time remaining in the current cycle. Pressing REGEN advances to the next cycle. Pressing once and releasing will schedule a regeneration at the preset delayed regeneration time. Error Screen Pressing again and releasing will cancel the regeneration. Pressing and holding for 3 seconds will initiate an immediate regeneration.
Front Cover and Drive Assembly Part No.
LIMITED PRODUCT WARRANTY Scope APEC takes pride in selling a superb line of products, including this Whole House Water Filtration (“Product”). As such, APEC expressly warrants to the original purchaser that, for a period of ten (10) years from the date of purchase, its tanks, valves, in/out non-electric heads, bypasses and fittings will be free from defects in material and workmanship.
CONDITIONS THAT RENDER THIS LIMITED PRODUCT WARRANTY VOID THIS LIMITED PRODUCT WARRANTY SHALL BE VOID IF: 1. The Product is not operated in compliance with normal municipal water conditions for which the particular model of this Product is intended. 2. The person seeking to invoke the warranty is not the original purchaser. That is, this Limited Product Warranty only extends to original purchasers. 3. The Product is purchased used. That is, this Limited Product Warranty only covers new products. 4.
Advanced Purification Engineering Corp. 301 Brea Canyon Road City Of Industry, CA 91789 For questions or comments please visit our website at: www.FreeDrinkingWater.com For technical support contact us at: Techsupport@freedrinkingwater.