User’s Guide Index 1
Index 2
Welcome to the new world of Maxpad™.
Index 4
Installation 6
1 Installation Installation 7
Remove your Maxpad™ from the box. As this is a product with a large screen, Maxpad™ is relatively heavy which requires detailed and careful handling. Due to this, before removing the Maxpad™ from the box it is recommended to read the instructions of this manual, in order to avoid accidents or possible damage to the equipment. Table or wall support: do not start without this First of all make sue that the table or wall support is unwrapped and ready to be fixed on the equipment.
Fit in the table or wall support. Table support 1. Remove the table support from the packaging; 2. Place the support on the table over the chosen furniture in the position where your Maxpad™ will remain installed (check image below); 3. If you have children at home it is recommended to screw the tale support on the furniture through the inferior holes. Even though Maxpad™ has a good stability, in case of fall it may cause serious damages, even cause death.
4. In two persons remove the Maxpad™ from the box and place it on the table support calmly and carefully. The support must be perfectly aligned to the central module of the rear structure. This will allow a perfect setting between the holes of the support and the nuts of the structure.
5. Fix the equipment with the two thumbscrews that come along with the table support. It is not necessary to use tools.
Wall support (sold apart) If you have chosen to install the Maxpad™ on the wall, follow the following steps: 1. Remove the four pieces that are part of the support, identified by the codes “1A”, “1B”, “2A” e “2B” the respective screws and plugs; 2. Remove the upper protection from the MaxpadTM (where this manual was place) and put it on the floor inverted; 3. In two persons remove Maxpad™ from the box and place it on the foam with the screen facing down.
4. Line up the rods “1A” and “1B” to the holes of the central module and screw with the aid of a screwdriver which follows the support, according to the drawing of the previous Page; 5. Fix the piece “2A” on the chosen wall (which should e made of brick and firm enough to hold the weight is 175 pounds). In order to make the work easier it is recommended to use the piece “2A” as a stretch to mark and make the holes on the wall, as shown in the next page.
For a person of medium height (5.
7.
Fixing the WideView lens to the camera. With the Maxpad™ already installed in its permanent place, remove from the box de plastic packaging of the WideView lens. With that in hands, remove the frontal sealing of the camera attached to the Maxpad™. IMPORTANT: AS THIS IS AN IMAGE DEVICE, WITH DELICATED SENSORS AND LENSES, THE SET SHOULD BE HANDLED WITH EXTREME CARE, TOUCHING ONLY THE PLASTIC AND METALLIC PARTS OF THE EXTERNAL BODY.
Indentify the accessories. Get to know the accessories that are supplied with the Maxpad™: Video Component Conversor / HDMI Cable of electricity Connects the Set Top box of the cable TV to MaxpadTM (through extensor of Video Component) with Full HD quality. Only through this cable it is possible to use all the resources of MaxpadTM which are related to the recording of content. Any other direct connection through HDMI will not allow the use of these resources if the Set Top Box has a HDPC blockage.
Video Component Extensor / Audio MaxRemote™ Allows the connection between the Converter of Video Component / HDMI and the Set Top Box of the cable TV. Even though it is an analogical transmission system, this cable offers the highest image quality, reaching the maximum resolution of the Maxpad™ (Full HD with 1920 x 1080 pixels) and a perfect audio, with no distortions or noises.
Exclusive Electricity Point Even though Maxpad™ has a low electricity consumption (around 300 W, depending on the size ofthescreen), it is desirable that it has an excusive outlet, or shared only with the set top box of the cable TV. The equipment has an automatic selection of voltage and it may be connected in 110V or 220V. It is recommended the use of a No break in case of tension alterations it is possible to preserve the integrity of the hardware and the Operational System.
Luminosity Condition and Sun Exposition Technology of optical touch screen As you may know by now, the new Maxpad™ also has the most advanced touch screen technology already developed for large screens, based on a complex system of micro cameras, infra red luminosity in optical fiber and math algorithms highly advanced.
Connect the Maxpad™ to the cable TV Maxpad™ is complete equipment which has the capability to work and perform various functions without any other peripheral device. However, in order to be able to use the advanced resources of interactive TV, the Maxpad™ should be connected to the Set Top Box of the cable TV or to any other device of video, such as DVD, Blue-Ray, Cameras, Video Games, etc.
Other inputs Besides the main inputs presented in the previous page, Maxpad™ also has three other inputs of video. Among them, one of them is already connected to the internal PC of the Maxpad™,which can be disconnected if there is the interest of using the product only as a monitor for another PC. The other two doors (one VGA and the other DVI) are available to be used in parallel to the internal PC of the Maxpad™.
2 Use Use 23
Identify the commands and connectors The first step to operate well your Maxpad is to know where the commands and connectors are located. Check the following general map: Lateral Panel LED Monitor 5MP FULL HD CAMERA On/Off Source Vol+ Vol- Menu Video Input Volume + Volume Options Menu USB USB 2.0 Door USB USB 2.
Rear Panel Maxpad™ is a product which offers various possibilities of connection. Check below the complete mapping of the interfaces of the equipment. Rede Ethernet 8 VGA USB 2 3 DVI Teclado / Mouse 1 4 HDMI OUT 5 Audio 10 SPDIF OUT USB 3.0 USB OUT 6 7 9 MIC 1. Pattern Connection PS/2 for key Panel or mouse 2. USB 2.0 Doors 3. Video Door VGA (D-SUB) – output for external monitor 4. DVI Video Door – output for external monitor 5. HDMI Video Door (occupied by MaxpadTM) 6.
A General View of do MaxRemote™ MaxRemote™ is an amazing accessory, that will facilitate not only the use of the Maxpad™ but also of all the devices that work with infra red technology. Inside the package of the MaxRemote™ it is possible to find a complete manual on how to operate and configure easily and fast your device. Below, it is possible to have an overview about this accessory. Face A - Universal Remote Control Function MaxRemote™ is a 3 in 1 product, which divides its functions in two faces.
Face B - Key Panel Function and Wireless Mouse (Wi-Fi) On Face B there are available the functions of Key Panel and Wireless Mouse, with Wi-Fi technology, which Will allow its work until 8 meters away (approximately, depending on the architecture of the environment). Even though the Key Panel is compact it has all the functions of a conventional key Panel and it has the ABNT2 layout, with the keys in Portuguese, that is with the “Ç”.
TV Function - Here it is possible to control the Maxpad™ Considering that the MaxRemoteTM has innumerous functions, in order to avoid confusion Apek will make a pre programming and the blockage of the “TV Function” on the MaxRemote™. That is, to use MaxRemote™ in the control in the Maxpad™ you need to select the “TV Function” of the MaxRemote™.
3 Interfaces Interfaces 29
Graphic Control Interfaces of the Device The Maxpad™ has basically two graphic, as shown below: 1. Control Interface of the LCD Panel ControlInterfaceoftheLCDPanel is a system that allows various types of image and sound configuration of the monitor integrated to the MaxpadTM. These configurations allow the control of color, brightness, distinctness, general volume among other resources.
Selection of Image Input (Source) Even though the Maxpad already has an integrated computer and it is connected to the HDMI Door of the LCD Board, in order to offer even more versatility to the product, Apek included two new inputs for video, one VGA and another DVI. These inputs are available in specific compartment placed in the rear of the Maxpad™ (as information and illustration on page 22).
Interfaces 32
4 Maintenance Maintenance 33
Special Cares and General Cleaning Ventilation Inputs On the rear part of the Maxpad™ there are various fans which have as objective allow a proper ventilation for the internal components. A series of energy source and silicon processors generate heat that with the thermodynamic assistance circulate through the internal chamber creating a natural air flow that properly cools down the equipment.
General Cleanness General Cleanness of the Maxpad™ must be accomplished with a paper towel or highly smooth fabric, slightly humid. Never use chemical products or abrasives because they may damage the paint or the integrated electronic components. In order to facilitate the removal of grease from the frontal touch screen glass use alcohol of high concentration (above 92°). Apply the alcohol in small quantities using a paper towel or fabric of high smoothness slightly humid.
Maintenance 36
General Key and Reset Besides the function “ON /OFF” (POWER) available in the MaxRemote™ an on the lateral selector board, in case of more severe failures it is recommended the use of the General Key of the equipment that when pressed it will make the complete “RESET” of the equipment, thus correcting eventual failures of the operational system.
Touch screen recalibration Due to the advanced technology of the optical sensor, the touch screen integrated to the Maxpad™ is already calibrated from the production and will never lose its calibration with its daily use. However, in extreme cases, with some peaks of energy or severe impacts, the screen may suffer slight variations and lose its original precision. For this, Apek makes available a software for calibration of the screen which is preinstalled in the Maxpad.
Cares with the transportation of the equipment It is necessary to transport the Maxpad™, it is strongly recommended to do so in the original packaging. This is the only packaging that will offer proper resistance and protection so that your equipment arrives at its final destination safe and sound. In case the packaging has been discarded, try to wrap the equipment using high density foam in all sides of the equipment.
Solution of usual problems Find below the solution for common problems that may occur in the Maxpad™: Problem found Possible Solutions Maxpad™ does not turn on when the Power Button is pressed on the lateral menu 1. Verify if the equipment is connected to the energy and if it has proper tension. 2. After pressing the Button Power wait for a few seconds and check if the indicative LED placed next to the Power is on and which color is shown.
O Maxpad™ does not turn on when I press the Power on the menu MaxRemote™ charging. 1. If it is charging, a LED indicator in blue will appear, always when a key is pressed. 2. Verify if the MaxRemoteTM is selected in the“TV” function (check page 28). If it is not, press the key in reference to the function TV and after the Power key. 3.Try to “aim” the edge of the MaxRemote™ toward the video camera integrated to the equipment or towards the lateral Panel.
Even with the volume of the monitor in high, there is no audio coming from the equipment 1.Verify if the central volume of the Operational System (Windows) is activated. 2. Verify if the Maxpad™ is in the function “mute” or if the Windows is configured in the “mute”. 3. Verify if the sound of the Maxpad™ is coming from the loud speaker of the MaxRemote™. If it is press the key “Fn”+ the key “Audio” in orange (placed on the space bar) to return the audio to the speakers of Maxpad™.
The image of the cable TV DVD/Blu Ray does not appear in the TV Maxpad applicative 1. TV Maxpad TV was not executed. In order to execute it click on the orange icon (MaxpadTV) placed on the main screen of the Widows 8 (Start menu). 2. Verify if the cable TV or DVD/ Blu Ray is connected properly through the Video Component through the cable of three colors – blue, green and red + audio (read and white) which comes with the product. 3.
The Wi-Fi signal is too weak 1. Verify if the external antenna is connected properly. 2. Check if the Wi-Fi router of the local is ON, working and in a distance to make the connection successfully.
General technical specifications Item Specifications Panel LCD Maxpad™ 39” Screensize: 39“ Dimensions of the active area: 853.92 mm (H) x 480.33 mm (V) High Contrast (3500:1) Fast reply time (9.5 ms) Full HDTV (1920 x 1080 pixels) - True HDTV with ultra large vision angle: technology Super MVA Vision Angle: 176 (H) / 176 (V) (CR > 20) in conformity with RoHS Life Expectancy of the LED: 50,000 hours Panel LCD Maxpad™ 50” Screensize: 50“ Dimensions of the active area: 1095.84 mm (H) x 616.
Painel LCD Maxpad™ 64,5” Screensize: 64,5”“ Dimensions of the active area: 1428.48 mm (H) x 803.
Touch Screen Technology (continuation) Frame Rate: 100 fsp Replytime:5-10ms ESD:Dischargepercontact: 8kV, Dischargethroughtheair:15kV Temperature for the operation: 0°C to 55°C Temperature for storage: -25°C to 125°C Humidity for the operation: 10% to 90%, non-condensed Transparency: > 92%, including the glass Frame Height: 4 mm Audio Two speakers - power 15W RMS Processor Processor A10 5800K Processing Cores: 4 (QuadCore) Cache L2: 4MB Integrated Graph (APU): ATI Radeon 7660 2GB / 256 bits Memory and
Integrated camera Cylindrical Aluminum body that permits Vision Angle adjust Resolution: 5MB Captures the videos in up to 1920x1080 pixels (Full HD) Manual focus adjust (optional) Sensor CMOS QSXGA for high quality image and low consumption of energy Technology of image active pixels clear and colorful, both precise in the reproduction Functions of Automatic Image Control: automatic exposition control (AEC), automatic white balance (AWB), automatic gain control (AGC), automatic band filter (ABF) Update Tax
Interfaces and connections 1 interface PS / 2 for keyboard / mouse 1 interface D-Sub (VGA) - for external monitor connection 1 interface DVI-D - for external monitor connection 1 interface HDMI (in use for the integrated PC) 1 interface of optical audio - connector S/PDIF 2 interfaces USB 3.0/2.0 6 interfaces USB 2.0/1.
Dimensions Maxpad 39” Without supports (mm): 961 (L) x 586 (A) x123 (P) With table support (mm): 961 (L) x 649 (A) x 286 (P) With packaging (mm): 1.300 (L) x 240 (A) x 840 (P) Dimensions Maxpad 50” Without supports (mm):1.197 (L) x 720 (A) x 123 (P) With table support (mm): 1.197 (L) x 783 (A) x 286 (P) With packaging (mm): 1.300 (L) x 240 (A) x 840 (P) Dimensions Maxpad 64,5” Without supports (mm):1.549 (L) x 924 (A) x 136 (P) With table support (mm): 1.
Maintenance 51
www.apek.com.
