Datasheet

ManualsBrandsApem ManualsJoystick & Navigation SwitchesBuilt-in Joystick

• Operating Force: 1.3N (2.86lbf) (Dependant on configuration)

• Maximum Load: 400N (89.921lbf) (subject to handle)

• Mechanical Angle of Movement: 36° X & Y axis (subject to limiter);

50° Z axis (subject to handle)

• Expected Mechanical Life: 10 million lifecycles

• Mass/weight: 100g (3.53oz) nominal

• Lever Action (centering): Spring

MECHANICAL SPECIFICATIONS

• Output Voltage Range: ±10% x V to ±50% x V

• Output at Center: V/2 ±(5% x gain)

• Power Supply: 5V ±0.5V transient free; 3.3V ±0.1V (configuration 2)

• Output impedance: 10 Ω

• Overvoltage max: +20V

ELECTRICAL SPECIFICATIONS

One, two or three axis

Analog or PWM outputs

Low profile less than 20mm below panel depth

5V or 3.3V operation

Metal mechanism

DISTINCTIVE FEATURES

• Operating Temperature: -25°C to +70°C

• Storage Temperature: -40°C to +70°C

• Sealing: IP65 (above panel subject to handle and final specification)

• EMC Immunity Level: EN61000-4-3 (extended)

• EMC Emissions Level: EN61000-6-3:2001, CISPR 22:2005,

Class B 30 MHz-11GHz

• ESD: EN61000-4-2 (extended)

ENVIRONMENTAL SPECIFICATIONS

3000 series

Robust proportional fingertip controllers •

non-contacting Hall effect technology

The company reserves the right to change specifications without notice.

JOYSTICKS

JOY-3000-1908

Summary of content (8 pages)

PAGE 1
JOYSTICKS 30 Y- JO 08 19 00 3000 series Robust proportional fingertip controllers • non-contacting Hall effect technology DISTINCTIVE FEATURES One, two or three axis Analog or PWM outputs Low profile less than 20mm below panel depth 5V or 3.
PAGE 2
JOYSTICKS 3000 series Robust proportional fingertip controllers • non-contacting Hall effect technology MOUNTING MATERIALS • Shaft: Stainless steel When mounting the joystick, care should be taken to site it in a position that does not make it vulnerable to damage when in use. If the joystick is intended for use in a handheld enclosure then care must be taken to protect the joystick from damage caused by dropping.
PAGE 3
Robust proportional fingertip controllers • non-contacting Hall effect technology MONTING (CONTINUED ) DROP-IN MOUNT CUT-OUT AND INSTALLATION • The joystick is dropped into the panel cut-out. • For panel thickness of <3 mm, m3 x 16 countersunk machine screws are recommended. • Please note: Image shows a square bezel, a circular bezel is also available for this option.. • For IP65 panel sealed, a sealing gasket 310062 need to be ordered separately.
PAGE 4
JOYSTICKS 3000 series Robust proportional fingertip controllers • non-contacting Hall effect technology BUILD YOUR PART NUMBER 3 SERIES CONFIGURATION LIMITER GAIN 1 Standard 10 ±10%xV A Single Axis 2 3.
PAGE 5
Robust proportional fingertip controllers • non-contacting Hall effect technology WITH HANDLE OPTION E C M J CM 60 2.36 MJ 32.25 1.27 20 0.79 4.50 0.18 18.00 (0.71) 35.00 (1.38) 29.60 (1.17) BL 25.00 (0.98) 12.70 (0.50) Ø31.30 (1.23) 42 1.65 D E Ø31.30 (1.23) 32.00 (1.26) 25.00 (0.98) 32.60 (1.28) 57.20 (2.25) 39.30 (1.55) 13.60 (0.54) K BK 29.52 (1.16) BK 29.52 (1.16) BK 12.00 (0.47) 49.25 (1.94) 32.00 (1.26) 50 R7. 95) (0.2 E D BL 16.25 (0.64) 12.00 (0.47) 13.
PAGE 6
JOYSTICKS 3000 series 39.30 Robust proportional fingertip controllers • (1.55) 22.00 (0.87) non-contacting Hall effect technology 13 .60 13.60 (0.51) (0.51) 39.30 (1.55) 49.25 (1.94) 22.00 (0.87) (CONTINUED) (0.51) 15.00 (0.59) 35.00 (1.38) 39.30 (1.55) 49.25 (1.94)9.30 (0.37) 13.60 (0.51) AC 22.00 (0.87) AK 13.60 (0.51) 15.00 (0.59) 35.00 (1.38) AC AK 49.259.30 (1.94)(0.37) AK 26.00 (1.02) 32.00 (1.26) 26.90 (1.06) 32.20 (1.27) 74.65 (2.94) AP 53.50 (2.11) 26.90 (1.06) 74.
PAGE 7
Robust proportional fingertip controllers • non-contacting Hall effect technology VOLTAGE OUTPUT OPTIONS SINGLE OUTPUT - CONFIGURATION 1 ±50% OUTPUT VOLTAGE (V) (+2.5) 5.0 (+2.5) 5.0 ±25% (+2.5) 5.0 (+2.0) 4.5 (+2.0) 4.5 (+1.5) 4.0 (+1.5) 4.0 (+1.5) 4.0 (+1.5) 4.0 (+1.5) 4.0 (+1.0) 3.5 (+1.0) 3.5 (+1.0) 3.5 (+1.0) 3.5 (+1.0) 3.5 (+0.5) 3.0 (+0.5) 3.0 (+0.5) 3.0 (+0.5) 3.0 (+0.5) 3.0 (+0.0) 2.5 (+0.0) 2.5 (+0.0) 2.5 (+0.0) 2.5 (+0.0) 2.5 (- 0.5) 2.0 (- 0.5) 2.0 (- 0.5) 2.0 (- 0.
PAGE 8
JOYSTICKS 3000 series Robust proportional fingertip controllers • non-contacting Hall effect technology CONFIGURATION POWER SUPPLY GAIN OPTIONS The 3000 series is designed to be powered by a regulated 5 V ± 0.5 V power supply. The outputs are ratiometric, making a stable, noise free, power supply essential. The 3.3 V version of the 3000 series requires a power supply accurate to ± 0.1 V. The voltage output on the wipers, at full scale deflection is determined by the gain.