Datasheet

ManualsBrandsApem ManualsIlluminated Pushbutton SwitchesIlluminated Pushbutton Switch 1NO 0.2 A/0.5 A 48 V/250 V IP67

APEM www.apem.com B1-15

IP series

Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary

Distinctive features and specifications

❑

Illuminated or non-illuminated

❑

Tactile feedback

❑

Wide variety of configurations

❑

Flat round actuator for optional marking

❑

Sealed to IP67

ENVIRONMENTAL SPECIFICATIONS

• Front panel sealing : IP67 according to IEC 60529

IP69K according to DIN 40050-9 (non-illuminated) with cap U5125

• Shock resistance : 100 g according to IEC 512-4, test 6c

• Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d

• Salt spray : IEC 512-6, test 11f

• Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule)

• Operating temperature : -40°C to +85°C

ELECTRICAL SPECIFICATIONS

• Max. current/voltage rating with resistive load (gold plated silver contacts):

5A 28VDC, 70.000 cycles

0,2A 48VDC, 500.000 cycles

0,5A 48VAC, 500.000 cycles

• Initial contact resistance : 100 mΩ max.

• Insulation resistance : 1 GΩ min. at 500VDC

• Dielectric strength : 1.500 Vrms

• Contact bounce : 10 ms

MATERIALS

• Case : thermoplastic UL94-V0

• Actuator :

polyamide

6/6

• Bushing/bezel : zinc die-cast

(zamac), black painted

• Contacts : silver, gold plated (std)

brass, gold plated (for option 104)

• Output wires

(flying lead terminals)

F version : AWG20, section 0,6 mm

W version : AWG24, section 0,23 mm

•

LED wires :

F version : AWG26, section 0,12 mm

W version : AWG24, section 0,23 mm

• Lens : polycarbonate

• Terminal seal : epoxy

GENERAL SPECIFICATIONS

• Panel thickness : 1,5 mm (.059) min.

4 mm (.157 max.)

• Total travel :

Funct. 3 : 1,7 mm (.067) +/- 0,3 mm

Funct. 5 : 1,3 mm (.051) +/- 0,3 mm

• Typical operating force : 6N +/- 2N

• Low level/mech. life : 1.000.000 cycles

• Torque : 1,5 Nm max. applied to nut

• Soldering : 320°C max. for 3 sec.

A resistor must be series-connected by the user.

Resistor value =

supply voltage - LED forward voltage

LED forward current

LED COMPONENT SPECIFICATIONS

LED colour

Forward current

Super red (L0S) 20mA

20mA

Typ. forward voltage Max. forward voltage

2,1V

3,2V

Yellow (L0Y)

Green (L0G)

Blue (L0B)

20mA 3,35V

2,3V

3,8V

4,25VWhite (L0W)

AGENCY APPROVAL

2A 125VAC/250VAC

File E83438

e following pages.

MOUNTING

Panel cut-out Matrix mounting

Back of panel space requirement

Ø13.60

(.535DIA)

(.531DIA)

Ø13.50

12.90

(.507)

1.50min-4Max

(.059 min-.157max)

20.00

(.787)

20.00

(.787)(.787)

20.00

(.688)

17.50

CIPCE1

➀ O-ring

For W terminals, current has to

be limited to 400mA.

UG1212-A-R1

Summary of content (6 pages)

PAGE 1
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Distinctive features and specifications UG1212-A-R1 ❑ Illuminated or non-illuminated ❑ Tactile feedback ❑ Wide variety of configurations ❑ Flat round actuator for optional marking ❑ Sealed to IP67 B1 ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS • Front panel sealing : IP67 according to IEC 60529 IP69K according to DIN 40050-9 (non-illuminated) with cap U5125 • Shock resistance : 100 g according to IEC 512-4, test 6c
PAGE 2
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Overview IP SERIES Electrical functions Actuator shapes C R P Square Round, curved Round, flat 3 5 Normally open (NO) NC/NO combined (non-illuminated) Terminals S F W P Z1 B1 Actuator colours 1 B 2 3 4 5 6 7/1 8 9 A Blue Dark blue Black Green Grey Yellow Red White Bright chrome Orange Satin chrome LED colours Blank L0S L0Y L0G L0B L0W Non-illum.
PAGE 3
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Square - illuminated • High brightness illumination • Five LED colours • Tin plated LED terminals LED Cathode (-) MODEL STRUCTURE B1 Shown with standard flying lead terminals. Also available with straight PC terminals : IPC3PAD LED colour is indicated by the bottom of the switch. 1.50 Min (.059 Min) EPOXY 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) 1.20 (.047) 2.00 (.078) 17.50 (.688SQ) 6.80 (.267) 5.00 (.
PAGE 4
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Square - non-illuminated • Double function (NC/NO combined) with a short behind-panel depth 8.70 8.70 (.342) (.342) 1.00 1.00 (.039) (.039) Function 3 (N0) CIPCOSP CIPCOSP CIPCOSZ1 CIPCOSZ1 Shown with standard flying lead terminals. IPC5SAD NC/NO combined Also available with straight PC terminals : IPC3PAD (NO) or IPC5PAD (NC/NO) and quick-connect terminals : IPC3Z1AD (NO only) 2.00 (.078) Ø12.00x0.75SI (.472DIAx0.
PAGE 5
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Round - illuminated • High brightness illumination • Five LED colours • Tin plated LED terminals LED Cathode (-) LED Cathode (-) MODEL STRUCTURE B1 Shown with standard flying lead terminals. Also available with straight PC terminals : IPR3PAD LED colour is indicated by the bottom of the switch. 1.50 Min (.059 Min) EPOXY 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) 1.20 (.047) 2.00 (.078) Ø17.50 (.688DIA) 6.
PAGE 6
IP series Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary Round - non-illuminated • Double function (NC/NO combined) with a short behind-panel depth Function 5 (NC/NO) MODEL STRUCTURE 2.40 2.40 (.094) (.094) 8.70 8.70 (.342) (.342) 2.80 2.80 (.110) (.110) 1.20 1.20 (.047) (.047) CIPCOSP CIPCOSZ1 CIPCOSP Shown with standard flyingCIPCOSZ1 lead terminals. Actuator marking available on IPP models (symbol 10 mm max.). On request. 5.00 (.196) Ø17.50 (.688DIA) Ø12.00x0.75SI (.