Datasheet

4
www.apem.com
STANDARD OPTIONS
Q 8 P 8 G XX Y 12 E
Q
1 = Solder
Lug/ Fastons
(2.8 x 0.8)
2 = Pins
3 = Wires
4 = Rear epoxy
Pins
5 = Rear epoxy
Wires
6 = Short body
Pins
7 = Short body
Wires
C = Bright Chrome
B = Black Chrome
G = Satin Grey
R = Red
G = Green
Y = Yellow
B = Blue
W = White
O = Orange
HR = Hyper Bright Red
HG = Hyper Bright Green
HY = Hyper Bright Yellow
HO = Hyper Bright Orange
SR = Super Bright Red
SG = Super Bright Green
SY = Super Bright Yellow
SB = Super Bright Blue
SW = Super Bright White
SO = Super Bright Orange
RG = Red/Green
RY = Red/Yellow
GY = Green/Yellow
02 = no resistor*
06 = 6VDC
12 = 12VDC
12A = 12VAC/DC
24 = 24VDC
24A = 24VAC/DC
28 = 28VDC
28A = 28VAC/DC
110 = 110VAC
220 = 220VAC
(Blank) = Unsealed
E = IP67
XX = Fixed Light
KK = Flashing Light
(12V – 28VDC)
YY = Bi-color
SERIES
MOUNTING
HOLE
8 = Ø8mm
P = Prominent
R = Recessed
F = Flush
BEZEL
STYLE
TERMINALS BEZEL FINISH
TYPE OF
ILLUMINATION
LED COLOR VOLTAGE SEALING
The Q8 Series is available with a range of standard options, to specify your LED, simply choose one option from each
column. An example is shown below.
Q SERIES Ø8mm (.315") Panel Mount LED Indicators
Overview
Example Q8P3CXXY02E
Ø8mm, prominent bezel, 200mm wire termination
bright chrome finish, fixed light, yellow
2VDC LED, IP67 panel sealed
• Gold Faston terminal denotes Anode (+), silver terminal denotes Cathode (-)
• Standard wire length is 200mm, 24AWG UL1061, red wire denotes Anode (+), black wire denotes Cathode (-)
for other wire lengths consult APEM
• For LEDs with alternative voltages consult APEM
• Bi-color LEDs, by connecting the gold Faston (+) one color is produced, by reversing the supply voltage
another color is produced – Bi-colors are available up to 28VDC. [AC products not available]
• Take care when soldering to the Faston terminals (recommended solder temperature 300°C - 3 sec)
• Terminal options 6,7 & 9 are only available up to 28V (DC Only) tri-color not available with terminal 9
• Terminal code 8 is only
available without integral resistor
•
•
Maximum panel thickness 7mm
We recommend using Hyperbright orSuperbright LEDs for use at 110VAC and 220VAC
8 = Short body
Lug/ Fastons
(2.8 x 0.8)
ZZ = Tri-color
RYG = Red/Yellow/Green
9 = Extended
short body solder
Lug/ Fastons
(2.8 x 0.5)
APEM
* = For resistorless versions (02) please refer to the forward voltage on page 1
• The Tri-color LED has red and green LEDs when both are connected yellow is produced
• Standard Tri-color Faston terminals are two Anodes (+) and one Cathode (-)
Tri-color wires are one red (+) and one green (+) Anode and one black (-) Cathode
• Tri-color pins are center (–) Cathode, shortest (+) Anode pin green, longest (+) Anode pin red
•