Installation Instructions

ManualsBrandsAperio ManualsAccess ControlProx Wireless Cabinet Lock Wholesale Kit 1:1 Hub Thumbturn in Black

Table Of Contents

K100-622 Aperio Series

Wireless Cabinet Lock

Installation Instructions

HES, Inc.

Phoenix, AZ

1.800.626.7590

www.hesinnovations.com

NOTE: The wireless hub and hub bracket are included with the K100-622H model.

Package Contents

Recommended Tools

Optional Additional Tools:

Gang box to mount hub

Cam Lock for Key Override

Drill, Drill bits: 1/16”, 3/16”, 1/2”

Approved iCLASS or Prox ID

credential.

Flathead drivers 3/32”, 3/16”

Phillips drivers P0, P2

Pencil, Wire Stripper, Level,

Square, Pliers

Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128-bit encryption

Hub Power Requirement: 8–24 Volts Direct Current (VDC), 250 milliamps (mA)

Lock Battery Type: Lithium AA Cell, 1.5 Volts (V) (Energizer L91 Ultimate Lithium)

Battery Life: 50,000 cycles

Operating Temperature: 32 °F to 122 °F (0 °C to 50 °C)

FCC Part 15 Compliant, IC Compliant

Credentials Supported: (-PA) Low Frequency model: HID PROX, EM PROX

(-SE) High Frequency model: iCLASS, iCLASS SEOS , iCLASS SE, ISO14443B UID

Mifare, Mifare Plus, Desfire SE, Desfire EV1, NFC

Product Specifications

For technical support please call 1-800-626-7590

QR codes can be scanned

with a smart phone app

K100-622

Tips and Videos

QR Codes

Strike Plate

Shaft Extension

2-56 x 1-1/4”

Energizer L91 Ultimate

Lithium Batteries

Double door bracket

Lock Body

8-32 x 1 1/4”

Breakaway

8-32 x 2 1/2”

8-32 x 2 3/4”

6-32 x 5/16”

6 x 1/2”

2-56 x 7/16”

Key Override

Cam

Key Override Paddle

Template

Screws

Reader

8-32 x 5/16”

Hub Bracket

Wireless Hub

3080076.004, Rev. B 1

Summary of content (12 pages)

PAGE 1
K100-622 Aperio Series Wireless Cabinet Lock Installation Instructions HES, Inc. Phoenix, AZ 1.800.626.7590 www.hesinnovations.com Package Contents NOTE: The wireless hub and hub bracket are included with the K100-622H model.
PAGE 2
System Overview The K100-622 series wireless cabinet lock provides access control to a cabinet or drawer without the complexity and expense of running wires to the cabinet or drawer. The K100-622 series lock connects to an access control through a communication hub (included with the K100-622H). The communication hub connects to the access control system with Wiegand wiring typical of a Wiegand Reader.
PAGE 3
Choosing the hub location NOTE: The following applies primarily to the K100-622H Model with included hub. It is recommended that the hub be mounted near the top of a wall, on the ceiling or above the ceiling to reduce potential for interference, and be facing toward the lock for best performance. For a stable and reliable radio link, it is recommended that the hub is located within fifty (50) feet of the lock.
PAGE 4
Connecting the Hub NOTE: The following applies primarily to the K100-622H Model with included hub. ® The Aperio Hub connects to the Access Control system via Wiegand wiring. The hub requires 8–24 VDC power (250mA). The hub includes three Form C relays that can be used to transmit latch bolt position status, low battery signal, and a tamper signal. The hub connects to the cabinet lock wirelessly. 1. CONNECT the Wiegand D1, D0, red and green LED signals. 2. 3. CONNECT 8–24 VDC and ground (250 mA).
PAGE 5
Testing the Lock with the Access Control System NOTE: With the hub connected to power and the access control system, the lock is tested with a known good credential to confirm it will open as desired when installed. 1. REMOVE the battery cover from the lock body. 3. CONNECT the wire (the wire is keyed) from the reader to the socket in the lock battery compartment. 5. PRESENT a credential known to the access control system. 2. PASS the wire and shaft from the reader through the lock body. 4.
PAGE 6
***CAUTION*** The Installer must ensure the lock can be opened before closing the cabinet at the end of these installation instructions. Mounting the Lock NOTE: C The K100-622 reader and lock body can be oriented in several ways to accommodate various cabinets and drawers. A 1. ESTABLISH the horizontal centerline of the latch. B D 1a. HOLD the lock body to the inside of the door and POSITION it generally where you would like it to mount. 1b.
PAGE 7
2. TRANSFER the location of the inside wall of the cabinet to the door. 2a. MEASURE the horizontal distance between the inside edge of the cabinet and the door edge. NOTE: The drawn line depicts the location of the strike mounting surface. 2b. DRAW a line on the outside surface of the door, using the same distance away from the door edge. 2a 2b Door edge Cabinet/door front view 3. PLACE and USE the Lock/Reader Template. NOTE: Orientation will be reversed for a right hand door. 3a 3a.
PAGE 8
4. INSTALL the Shaft Extension. 4a. IF the cabinet door thickness is greater than ½”, THEN INSTALL the Shaft Extension to the Antenna/Reader to ensure proper engagement into the lock. 4b. INSTALL the Shaft Extension to the shaft as shown in the figure and firmly TIGHTEN the screw. Shaft Extension 2-56 X 1-¼” screw (provided) Table 1 Door Thickness Extension Shaft Used? 1/16” – ½” No > ½” – 1 ½” Yes 5.
PAGE 9
7. INSTALL the Antenna/Reader. ***CAUTION*** Pinching the wires may prevent the Reader and Lock from properly functioning. 7a. PLACE and HOLD the antenna/reader to the outside of cabinet, routing the wire through the 1/2” offset hole, and ENSURE the knob is in the locked position in the vertical. 7a NOTE: Using the Table 2 below will help determine the length of the top mount screw needed, based on the thickness of the cabinet door. 7b.
PAGE 10
9. Electrically CONNECT the antenna/reader wire to the lock body. NOTE: The antenna/reader wire connector is keyed to only fit one way. 9a. ENSURE correct orientation of the connector while inserting it. Connector cable tucked in 9a 9b. TUCK excess cable into lock body as shown. 9b 10. INSTALL the Batteries. NOTE: New batteries should always be used and inserted in the correct polarity position. 10a. INSTALL the battery and battery cover. 10b. INSTALL and TIGHTEN the screws. 10b 10a 11.
PAGE 11
***CAUTION*** The Installer must ensure the lock can be opened before closing the cabinet. 12. INSTALL the single-door strike plate. 12a. PLACE the strike plate over the pilot holes, and INSERT and TIGHTEN the two screws in the slotted holes. 12b. CLOSE the door to verify installation, and ADJUST the strike plate if necessary. 12d. INSERT and TIGHTEN the lock down screw on the strike plate. 12d 12a–c OPTIONAL DOUBLE-DOOR INSTALLATION 13.
PAGE 12
WARNING FCC Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.