Universal Remote Model: 39900 & ONA12AV058 PRODUCT MANUAL
Table of Contents Introduction............................................................ 2 Battery Installation.................................................. 3 Care and Maintenance...................................... 3 Button Functions.................................................... 4 Programming Your Remote.................................... 6 Direct Code Entry.............................................. 6 Auto Code Search.............................................
Battery Installation Your universal remote requires two (2) AAA Alkaline batteries (not included). To Install the Batteries: 1. Remove the battery compartment cover by sliding the cover down. 2. Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AAA Alkaline batteries. Be sure to use fresh batteries. 3. Slide the battery compartment cover back into place.
Button Functions TV, CBL/SAT, VCR/AUX, DVD Selects the device to control. ON•OFF Turns the device On or Off. EXIT Exits OnScreen Menus. MUTE Turns off the TV sound while the picture remains. In SHIFT mode OK Selects menu items for the device you are controlling. INPUT Selects the video inputs from available viewing sources. NUMBERS Enter numbers for direct channel selection. DOT: Used to select digital channels, for example: 4.1, 9.
Button Functions, cont. MENU displays the Menu on the TV and other devices. Use the SHIFT button to access this feature. ? (INFO) displays/selects on-screen channel information, etc. VOLUME UP/DOWN Changes the volume level of the device, normally the TV. CHANNEL Up/Down Changes the channels. In SHIFT mode, these buttons navigate onscreen cursors and are used to make selections. SETUP button is used to program the remote. SHIFT is the alternative function of this button.
Programming Your Remote Your ONN universal remote control is designed to control up to 4 different audio/video devices such as TV, DVD, VCR, satellite, cable and audio using only one remote. To use this remote, you will need to program it to control the devices of your choice. There are two ways to program the remote - direct code entry or auto code search. Direct Code Entry (Recommended) 1. Locate the Remote Code List provided in this manual.
Programming Your Remote 6. Point the remote at the device. Press the POWER button—if the device turns off, no further programming is required for that device. If the device does not turn off, return to step 3 and use the next code found in the code list. Continue this process until a code for your device is found. To view a helpful demonstration video for programming your ONN remote, see QR code on page 2 of this manual.
Programming Your Remote Auto Code Search The Auto Code Search searches automatically through all of the codes stored in this remote. Read all the following steps prior to starting the auto search as you will need to be prepared to lock-in the proper code when found. 1. Manually turn on the device you wish to control. 2. Press and hold the SETUP button until the red indicator light stays on (approximately 4 seconds) and then release the button. 3.
Programming Your Remote To view a helpful demonstration video for programming your ONN remote, see QR code on page 2 of this manual. Programming Notes • This process may take several minutes as the remote contains many codes. • The SETUP button can be used during the search process to reverse the direction of the search of the remote codes.
Master Volume Feature Master Volume Feature The Master Volume Feature allows you to select a single device (TV or audio receiver) that the volume control always controls. For example, the remote can be in TV mode while the volume buttons control the volume on your audio receiver instead of your TV. Enabling the Master Volume Feature 1. Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button. 2.
Master Volume Feature, cont. 2. Press and release the device button (TV, DVD, SAT, AUX) which is programmed to control the Master Volume Feature. 3. Press and release the MUTE button. 4. Press and release the VOL button. The red indicator light will blink twice and go off. To make sure the Master Volume Feature is disabled, put the remote in TV mode if you programmed the audio receiver to be the Master Volume Device. Point the remote at the TV and press a volume button.
Troubleshooting Remote does not operate your device. • Make sure the batteries are fresh and installed correctly. • Aim the remote directly at your device, and make sure that there are no obstructions between the remote and device. • Make sure you select the appropriate device on the remote you wish to control, for example, TV for TV, DVD for DVD, etc. • Try programming the remote with a different code. See Direct Code Entry section. • Remote may not be compatible with your device.
FCC Statement FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.