User's Manual

Step 1
Step 2
Step 3
Step 4
Turn on Power
Start motor
Ascent/Descent (Push/Pull throttle)
Direction Lever
GPS
Put the lithium battery into the battery
compartment, according to the instructions
The direction of the arrow is shown on the
head of the aircraft.
Push into the battery and hear the "ka" snap
sound; check if the battery fitting is tight.
To remove the battery, push out hardly per
battery arrow direction.
Push the battery in the direction of the head.
LED instruction Charging specification
Lights off
Light on
Charge Completed
Charging
Input
5V 1A 4.2V+_0.03V
Charging Current Full Voltage
Battery and charge specification
Battery type Battery specification Using time Charging time
Lithium polymer
battery
3.7V 800 mAh Drone Flight time : 7-8 mins
About 60 mins (charging
current approx 1A)
Caution
Short press to switch speed
Headless mode
Throttle lever
One key to take off/
One key to land
On/off
Short press take photo /
Long press to take video
One key to return
Directional rocker
Trim(left/right)
Trim(forward/backward)
Calibration between drone and controller
Step 1
Step 2
Step 3:
After the frequency is matched, please perform compass calibration.
Level
Turn on / off
Light stable
1.Turn on:Short press the switch button, the remote
control enters normal working mode, the buzzer
emits a short sound and the power indicator flashes.
2.Turn off: long press the switch button, the buzzer
emits a short sound, power indicator light is completely
off, and remote control enters the shutdown state.
Unlock
Blades rotating
First turn on the remote and then turn on the drone.
At this point, the remote control emits a "beep" sound,
and the drone indicator light is always on, indicating
the code is completed.
Move the throttle lever to the lower left corner and
move the directional joystick to the lower right corner
(simultaneously
) to start the motor. Release the
rocker after the motor starts.
Throttle control
Landing
Fly
Pull the throttle lever up ,drone will fly up.
Pull the throttle lever down ,drone will fly down.
Set the throttle in the neutral position, the height
of the drone remains unchanged.
“
After unlock the drone ,press “One key to take off
/ land”button ,drone will hover about one
meters above the ground.Press again, drone will
land automatically.
Turning
After the drone is lifted off, the throttle stick is
rocked left and right, and the drone turns left
and right.
Forward / Backward
Pull the direction lever up, drone will fly forward.
Pull the direction lever down,drone will fly
backward.
Left and right
Push the direction lever left, drone will fly to left.
Push the direction lever right, drone will fly to right.
Trim
Take photo/video
Short press the “Photo/Video” button to take a photo,
long press this button to record a video. Photos
and videos will be saved in your app.
Short press to change speed
Short press to switch speed,long press to 3D flips.
1.speed (low ) :"beep" 1 time.
2.speed (medium ):"beep" twice.
3.speed (high ) :"beep" 3 times
Headless mode
One key return
APP application and description
APP download and installation
Download the app according to your mobile phone system model, as follows:
1. Android system
A: Search for the keyword ‘‘AT-246 GPS’’ in Baidu mobile assistant APP
(android market or 91 Assistant) to download.Search for keyword‘‘AT246-GPS’’
download.
Or use a browser to scan a QR code to download. If scan code download fails ,
please download in Baidu mobile assistant APP.
B:On Google play: search for the keyword ‘AT-246 GPS’ to download.
2. ios system
Please go to APP store ,enter the key word “AT-246 GPS” to download the app.
Operating instructions of APP
1.After installing the APP on the phone ,click enter and the following screen appears.
Aircraft GPS
Satellite number
Distance Height Horizontal speed
Vertical speed
WIFI
State
Add unlock status
Power State
Rocker
Gravity sensor
GPS follow
Current state of
the aircraft
Camera
Take a photo
Camera settings
Album
Throttle rocker
One key to take off/ land
Compass
One key to return
Directional rocker
Setting
2.The Wifi connection
AT-246 GPS@XXXXXXX
GD145_XXXXXX
(1)Please open your drone first and connect your mobile WIFI hotspot to AT-246 _GPS_XXXXXX”.
(2)Enter the APP .if the mobile app is successfully connected to the drone ,you can see real-time
image transmission in the app. It can be controlled remotely by a mobile phone.
(3)The remote control is invalid when the mobile controls the drone; mobile phone control is invalid
when the remote control controls the drone.
3. Rocker
When the joystick is turned on, the drone indicator light is always on, and the virtual handle can be used for flight.
4.Please refer to P4 & P5 for throttle and direction control.
5. Taking pictures
Trigger the APP photo function;Short press the remote control also can take photos.
6. Camera
Trigger the APP camera function, the camera starts, triggers the camera to stop again; long press the remote camera
function can also take the camera.
7. Gravity induction
Triggering gravity sensing, the direction of the Earth's gravity is sensed by the built-in sensor chip of the mobile phone
to control the direction of the drone.
8. WIFI status
This icon shows signal strength of the drone connected to the remote.
9. Battery status
Shows power of the drone.
10. Photo album
Click on this to view photos and video you take.
Installation protection frame and replace the fan blade
Installation protection frame
Install the protective frame as shown in the figure and use the accessory screws to tighten the protective frame.
Replace the fan blade
In order to achieve the best flight function, the blades need to be inspected or replaced with new blades after multiple flights.
Especially when flying in high altitude
May damage the blades.
1. When replacing the blades, make sure that the letter 1 on the fan blade is the forward fan blade, 2 is the reverse blade,
and the letter is on the back of the blade.
2. Pay special attention to replacing the damaged blades with the correct turning blades. Don't change the steering blades!
FR
F
R
Front left positive blades= F
Back left reverse blades=R
Front right reverse blades=R
Back right positive blades=F
Trouble shooting
1
2
3
4
5
6
Troubles
Causes Ways to deal
Turn on the drone and the drone
lights continue flashing, no
response
The remote controller and the
receiver are not successfully
matched.
Please re-execute the counter action of the
remote control and the receiver board.
(Please refer to the frequency alignment of
remote controller and receiver in P3)
Turn on the drone, the drone has
no reaction to commands
The battery died
Charge the drone battery
Blades keep moving after
landing
Throttle lever is not at the zero
position
Put the throttle lever to zero position
Blades keep moving , while the
drone can not take off
1.Blades may be installed
incorrectly
2.No enough power
1.Change the blades
2.Charge the drone battery
After trimming ,drone keeps
spinning,
and the speed of
blades is different
1.Blades may be installed
incorrectly
2.Blades get damaged
3.Calibration failed
1.Install the blades
2.Replace the blades
3.Refer to p3 for calibration
The drone can not take off after
drop
1.Blades are getting lose
2.Blades get damaged
1.Tighten the blades
2.Replace the blades
Children under the age of 14
are prohibited from using.
Warning:
4
5
6
7 8
1
2
3
AP-X240-GIMEN
Quick Start Guide
Features
Features
Standard components
Standard components
Battery charging and installation
Battery charging and installation
Model: X-240G
Remote control function key description
Remote control function key description
1
2
3
Compass calibration
Calibration between drone and controller
4-5
Remote control instructions
Remote control instructions
6
7
APP application and description
Operating instructions of APP
Installation protection frame and replace fan blade
8
Trouble shooting
User Manual
4*Protection Frame
Ascent
Descent
Tuen left
Turn right
Fly forward
Fly backward
Right
Left
1*Drone 1*Controller
1*Charging box
1*USB Charger
1*Screw driver
2*Battery
4*Propellers
1*User manual
Headless mode
One key to take off/land
One key to return
Speed adjustment
Follow me mode
Battery charging
1.Remove the lithium battery from the drone, insert one end of the
charging cable with the USB port into the phone adapter interface,
and then the interface with the plug on the other end is correctly
connected to the battery socket.
2.Plug the charging cable into the USB port of the computer host.
the method is the same as above ,and the charging can also be
completed.
3.The indicator light is always on other the charging state, and it
will automatically crush out when the battery reaches the full state.
Notice:
During the flight ,when you hear the :beeps” sounds from the remote control,it indicates
that the Drone’s battery voltage is not enough ,so the drone should fall behind to recharge .
it need to charge it with the special charger we give/provide.
During the flight, when the remote control indicator lights flicker. It indicates that the remote
control battery voltage is not enough ,please replace the remote control battery.
Compass Calibration
Please select an empty space and follow the steps below to calibrate the
compass.
1.As shown in the figure: Move the remote control rocker in the direction of the
arrow for 2 seconds, and wait for all the lights of the drone to flash slowly.
2. Rotate the drone three times horizontally (put the drone on the horizontal plane,
hold the drone by hand, rotate it 3 times on the horizontal plane), and the status
indicator of the drone is red.
3. Hold the drone head up with the hand (the drone is in a vertical state), rotate it 3
times horizontally, and the drone status indicator is green.
4. Calibration failure if drone all indicators are flashing,please replace the takeoff
ground to recalibrate the compass.
5.When aircaft status indicator flashes red after calibration, it means the stars are
not enough and novice/beginner is not recommeded to take off.
Cautions
Compass calibration: Please calibrate the compass before using the drone. If the drone moves more than 50
kilometers, you need to calibrate the drone again before you can use it.
Vertical calibration
Horizontal calibration
Replace the fan blade diagram
Turn on remote control switch button firstly, turn on the drone power
switch secondly.Point the drone tail to you and put it on a horizontal
plane,remote control will emit "beep,beep beep"sounds,which means a
successful device match.
As shown in the picture, push both joystick of the remote control to the
lower right corner. When the indicator light of the drone flashes quickly,,
released the remote control and wait for the indicator light keeping on
lighting. The remote control will emit””beep beep” sounds and the
calibration is completed.
Important note: Turn off the drone requests long- press on power switch.
Because the internal gyros need to be horizontal calibrated after the
drone is open, therefore , must put it in horizontal surface place.
If long time note used it, please take out the battery of the remote control,
and keep it properly. Warn: It will lead to batter leakage and remote
control damaged, even a fire if battery is kept for long term w/t use and
stays in the remote control.
Start and settings: short press the headless mode
button, the remote control beeps twice, the drone
indicator flight flashes slowly, headless mold starts,
the direction of the drone’s head is the front. If there
has a crash or flying forward deviation, please restart
to adjust the required direction frequency.
Exit: short press the headless mode button again,(the
remote control beeps and the drone indicator light is
always on), headless mode exits.
In headless mode, no matter which direction the lead
of the drones turns, the current position of the remote
control is right behind of the drone. Pull down joystick
to recall the drone, push up to fly far.
Short press the smart return button until buzzer
beeps” Bi, bu, bi”, the drone will return to the latest
researched star confirmation point. Cannot
manipulate the drone during return voyage.
Another sort press on this button to end voyage.
After the drone is lifted off, when the drone is shifted
in one direction without manipulating the corker.
Deviation canbe adjsuted by trim-buttom.
Correct drone movement via opposite direction.